• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Autowatch Ghost Immobiliser Installation

The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It's discreet, doesn't use keys or LEDs and is hidden within the vehicle's wiring.

The user can also disable the system temporarily using Transport Mode when renting their car. This guide will walk you through the installation of a Ghost immobiliser.

Professional Installation

The Autowatch Ghost immobiliser protects your car against key cloning attacks, hacking attacks and relay attacks. The system is linked directly to the ECU of your vehicle and protected by a PIN code you select. It is inaccessible to thieves using diagnostic scanners or other modern methods, and it is unable to be disabled by circuit cuts.

The system is simple to use, but professional installation is advised to ensure a perfect connection to the ECU of your vehicle. An approved installer from Thatcham can assist in the installation and programming of your Ghost system. They can also suggest a tracking device or alarm to complement the protection package for your vehicle.

First, the installer needs to disconnect your battery to prevent accidental airbag deployment or short circuits. After this is completed the installer is able to safely begin work. Basic hand tools can be used for precise connections. A multimeter is useful to check electrical values. Cable tie and insulation tape are essential to protect connections and keep wiring tidy. Lastly, the user manual gives specific guidelines that are specific to the Ghost Immobiliser model you have.

It is essential to choose the right grounding spot that is free of dirt or paint during installation. The installer must ensure that the immobiliser's CAN H and CAN L wires are connected to the correct ports on the vehicle's ECU. Depending on the model, these wires might require soldering or plugged into. Using a top-quality connector is recommended to ensure a sturdy and secure connection.

Transport Mode can be activated by the client after the installation is complete. This allows mechanics or valet parking to use the vehicle, without knowing the pin code. To accomplish this, the user must hit the service button on the dashboard 5 times in the space of two seconds. The system will confirm this by showing five indicators.

The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's a smart choice for anyone who frequently rents out their vehicles on platforms like Turo. An immobiliser can cut down on the cost of insurance, as it decreases the likelihood of theft.

Getting Started

If you're looking for a solution to safeguard your vehicle from theft it is best to go with an autowatch ghost immobiliser. The device prevents your vehicle from starting if someone steals or copies your key. It is possible because of its advanced technology, [Redirect Only] which prevents the engine from starting until the right PIN code has been entered.

The device connects to the vehicle's bus network, CAN, allowing direct communication with the ECU. It uses the buttons on your steering wheel and dashboard to create a unique sequence, that only you can understand. This makes it impossible for anyone else to start your vehicle. This is the ultimate system to protect your pride and joy. It will ensure that your car's value remains intact if you ever want to sell it.

Installing a ghost ignition is an easy procedure, but it is important to follow the instructions carefully to avoid problems with the electrical system and malfunctions. First, you must find a 12V power source and a solid grounding on the chassis of your car. Then, you can begin connecting the wires that will be used to activate the immobiliser. Use high-quality connectors, and soldering methods to create a secure connection. Connect the connections with heat shrink tubing or insulation tape, or other materials to prevent electrical short circuits.

After the wires are connected, you can connect the battery and start the engine to test if the immobiliser is working. After you've confirmed that everything is functioning properly, you can install the immobiliser in a safe place inside the vehicle. Make sure you hide it properly to stop any thief from taking advantage of it.

The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified, which means that it complies with the highest standards of security and is an excellent protection against car thieves. It is resistant to key cloning and hacking and cannot be disabled without the code. It is simple to use and can be set to the service valet setting to ensure that your vehicle will not be activated when you take it for an MOT or servicing.

Wiring

The ghost immobiliser review Immobiliser, a cutting modern security system, was designed to deter theft of vehicles. It communicates with your vehicle's ECU and directly connects to its CAN bus. The Ghost Immobiliser does not interfere with the factory settings of your car immobiliser ghost, unlike other aftermarket systems that require the removal of circuit elements.

The system is also undetectable by thieves using scanners for diagnostics. This is because the system doesn't send and receive radio frequency signals, and it relies on CAN data to communicate with your ECU. It also doesn't require modifications to your existing key fobs.

Enter the sequence to disarm (either two or one button) and then turn on the ignition in your car to activate Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. After this, you can start your vehicle and drive off safely.

Once installed, the Ghost Immobiliser will secure your vehicle from key cloning and hacking, while protecting the value of your most prized possession. If you ever need to hand over your vehicle to valet parking or for service The ghost immobiliser and tracker Immobiliser can be temporarily disabled in Transport Mode.

You'll require a constant power source (12V) in addition to a grounding point to complete the installation of a Ghost immobiliser. Make sure that both are well-insulated and able to be touched. It is also recommended to use cable ties to tie and secure the wires. This reduces the risk of tampering by potential thieves. Make sure you double-check the position of these points to avoid making mistakes, and mark them with an adhesive or label. It's recommended to check every connection for signs of wear and tear. Connectors that are loose could cause malfunctions in the system, so make sure they're securely in place and properly insulated. Don't forget to test the Ghost Immobiliser after the installation is completed. This will make sure that the unit is functioning correctly, and that all connections are safe and well-insulated. If you encounter any issues, be sure to address them immediately.

Testing

The Autowatch ghost autowatch immobiliser immobiliser is a revolutionary vehicle security system that integrates seamlessly with your car's ECU to prevent the motor from starting without authorization. Its cutting-edge technology protects your vehicle against hacking and key cloning as well as other methods commonly employed by thieves to steal vehicles. The Ghost also works in conjunction with existing alarm and tracking systems to provide the most complete protection for your vehicle. The Ghost's unparalleled features, combined with its discreet design makes it a sought-after choice for drivers who love cars and security-conscious drivers.

To ensure the proper integration of the Ghost Immobiliser, it's important to follow every step of the installation procedure. A good starting point is to consult the wiring diagram for your vehicle that will serve as a guideline to locate and connecting the necessary wires. Then, you'll need to identify the power source and grounding points. Once you've found them, you will be required to mark the points to make them easy to locate when installing. It is essential to use top-quality materials and tools. Basic hand tools can assist with making precise connections and a multimeter can confirm electrical values and guarantee security. Cable ties and insulation tape will help keep all connections tidy and neat. Finally, a user manual will provide specific guidance specific to your Ghost model.

It is crucial to test the system prior to installing it. Enter the PIN code into the system and then start the vehicle. This will ensure that the immobiliser is working as it should and prevent unauthorised vehicle starts. It's recommended to perform this routinely as part of your regular vehicle inspections to ensure that the system is always functioning correctly.

After the installation has been completed, you are now able to start driving your vehicle with confidence. The Ghost will help keep your car and its contents safe from potential thieves and ensure that nobody is able to escape with your car without the proper PIN code. The Ghost can be paired with an approved Thatcham tracker that detects any attempts at theft or tampering. This allows you to track your car in the event that it's stolen.

The Ghost is compatible with a wide variety of vehicles, including those made by most major manufacturers. Monty's Locksmith can assist you in securing your vehicle using this cutting-edge device. Contact us today to learn more about our service and installation options. We are a TASSA registered installer, which guarantees we follow strict standards in the installation of our products. This guarantees customers, insurance companies, and law enforcement agencies that all installations are done safely and in a safe manner.