• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

It is easy to repair a damaged window handle with the right tools. It is important to know the handle's type and spindle's length prior to purchasing the replacement.

Older uPVC window handles have a spur that protrudes and locks over the wedge striker for cockspur. They can be left or right-handed and must be to be replaced with the same handle.

What kind of lock and handle do I have?

There are a myriad of windows locks and handles made of upvc, each with its own advantages and purposes. The type of handle that you own will determine if your locking mechanism is efficient and if it's easy to open windows. With time and regular use the handles made of upvc on your windows may become damaged and worn out. This makes them less secure and effective. In some cases they may even fall completely off. It is crucial to fix your upvc window handles immediately if you notice they are falling off. This will prevent possible break-ins, and keep your house safe.

The good news is that replacing your window handles made of upvc is a fairly simple job that can be completed by everyone. With just a few tools and the right knowledge it's a simple procedure that shouldn't take less than a few minutes. You will need to know the kind of lock or handle you have on your window. This will allow you to choose the appropriate replacement window glass.

Inline Espagnolette Handles

They are typically found on the outside of the window. They are flat and feature a latch which engages the locking mechanism of the window sash replacement frame. Inline upvc handles also have a spindle that goes through the middle of the handle and then into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and feature a distinctive, hook-shaped design. Cockspur handles are secured to the window frame by a single screw and are less secure than other varieties of window handles.

Tilt and Turn Handles

As opposed to the other handles made of upvc that are tilt and turn, these handles can be rotated to open the window and turned inwards to allow to allow ventilation. They feature a 7mm spindle at the back and are available in right and left-handed versions.

When purchasing replacement window handles made of upvc it is essential to measure the spindle's length as not all are identical in size. To determine the length of your upvc handle simply drop something into the middle of the hole and measure the distance it travels before it reaches an obstruction. This is the length of the spindle that will fit in your window.

What is a spindle?

uPVC window handles function similarly like doors. By turning the handle, you will be able to open a latch in the frame. The latch opens the window, so it can be opened and closed. However, in some cases, these handles can become damaged, especially if they are regularly used or exposed to extreme weather conditions. This can leave you needing to replace your uPVC handles on windows since they may not operate the window correctly for a long time.

There are a variety of uPVC handle options, such as Espag, Cockspur, and Spaded handles. These handles are designed in a variety ways to fit into uPVC frames. Each handle type utilizes a different spindle to lock the window mechanism. This is why it is crucial to know the type of handle is installed on your uPVC window to get the correct replacement.

The base of the handle will tell you what kind of uPVC it is. A snap-in cover should be over the screw that holds the base of the handle in position. After removing this, you will be able see the screw that holds the base of the handle in position. After both screws have been removed then you should be able to remove the handle from the uPVC.

Once you have removed your uPVC window handle you need to carefully remove the spindle you have removed from the locking mechanism. Note the length of the spindle. You will need to purchase a new one that is the same length as the original handle and the locking device.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to damage from constant use or a loosening of the locking mechanism, or even rust over time. If this happens, you will need to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.

How do I remove the handle that was previously attached?

Over time and through everyday usage, window handles could be damaged or destroyed, and when this happens, it is important to repair them as soon as you can to ensure the security of your home. It is simple to replace a worn or damaged handle. The job can be completed in under an hour without the need of special tools.

The first step in removing the handle that was previously used is to remove the screw that is located at the top of the base of the handle. Once the screw is removed, the handle will be pulled away from the base section. A second screw will be located at the base of the handle. It can also be removed. Once these two screws are removed, the handle can be removed from the window's base.

After removing the handle, align the fixing holes of the new handle with the holes already present in the window frame. There might be a small sticker or caps on the new handle, so take them off these if necessary and then put the handle in the frame. It is crucial to verify that the handle works once it has been installed. Turn the handle over and make sure the lock mechanism is activated.

Espag handles feature spindles that extend out of the handle and slot into the multipoint locking mechanism on the frame of the window. Cadenza windows have blades with cut-outs that slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over either the frame's outer or the transom bar cross member inside the window.

Once you have the new handle in place, insert the spindle into the window lock and then tighten it down. Once the handle is firmly fixed then replace the snap-in cover and screw cap (if applicable). When the handle is ready to use, open and close the window a few times to make sure that it functions correctly and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is very simple. All you need is a screwdriver, and a little bit of patience. First, ensure that the handle is not locked. Then remove any visible screws. You could also replace them with screw caps. After removing the handle you will need to note the length of the spindle that extends from the back. This is important because it will determine the type of handle you need to buy.

Espagnolette handles are the most popular type of handle used on uPVC windows. They feature a spindle that is connected to the handle and operates an internal locking mechanism within the window frame. The handle opens the latch and allows the window to open. During regular use and time, handles for espagnolette may be damaged.

Cadenza handles are a different kind of uPVC window handle that is commonly used on tilt and turn windows. They feature a protruding blade that works with a multiple-point locking mechanism inside the window. They are generally more secure than espagnolette handles since they are only accessible from the inside. They can be replaced with the same method as espagnolette handles but you should make sure that the new handle has an angled blade as opposed to one that is flat.

Once you have determined the right handle to purchase You can simply place the new handle with the existing screw holes and then screw it into the appropriate position. You should then put the screws back on and verify that your new handle is operating correctly. You can accomplish this by dragging the handle between the locked position to the unlocked a few time. If you encounter any issues, it could be beneficial to speak with a professional to see if they are able to assist you in solving the issue. They can provide advice on how to fix the problem in a timely and efficient way.