• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

If you're replacing your handles or want to add a bit of extra security you can find the right handle for your door. These upvc handle are easy to install and have the minimum 92mm center distance of multipoint locks.

The backplate fixing centre and the keyhole/lever dimensions are the most important measurements. Compare these measurements carefully with your existing marks before ordering.

Lever/Pad

Lever pad handles for doors consist of a lever handle on one side and a paddle-shaped handle on the other. These are designed to work with key wind locks, however they can also be fitted to split spindle multipoint door locks (though you'll require a separate dual spindle lock case).

Our selection of upvc handle lever pads are available in a variety of finishes and these will be listed in the drop down list after you have identified the right handle for your doors. Not all styles of handles are available in every finish and you should always check the sizes and technical drawings for the specific product you want to make sure that you can get the right size and fit.

It is essential to ensure that when you choose a new set of Upvc lever pad handles, they are in line with the PZ (distance from the handle spindle to the middle of the hole in the cylinder) of your multipoint door locks. This is because the handles are required to be aligned for the doors to stay locked, whether you are looking at them from the inside or from the outside. Our handles are designed to fit a wide range of conventional cylinders, but it is important to double-check before purchasing.

If you want to upgrade to dual spindle levers you will need to remove the handles that are currently in use and then take apart the lock case. This will require an additional split inline cylinder. You can purchase these separately. We have included a technical diagram in the images of each product.

It is a good idea to loosen the screws that are holding your door handle, and then check the mechanism. If the screws aren't tight enough then you might need to loosen them further. Then you can remove the spindle from the handle and replace it with a new upvc handle. Before you screw the handle into place it is recommended to check that it is in the proper position. You can do this by placing your finger in the gap between the frame of the door and the door handle to ensure that it is in a level position.

Lever/Lever

The lever handles for internal bifold doors for doors are used to operate a multi-point lock using the Euro cylinder. They are located on many double upvc doors, as well as on some wooden and aluminum doors. They are available in two forms, having a lever on the interior and a paddle on the outside. Sprung - these come with a spring cassette inside the backplate to bring the handle lever to a horizontal position. Non-sprung - they do not have a spring mechanism, and will require manual pulled to bring the handle lever to the horizontal position.

To fix a door handle that is sagging it is necessary to find the hole for access to the detent or pin, which is usually a small round or rectangle with a protruding hole situated on one side of the base plate. Once you have located the detent access hole or pin, you are able to remove it with an screwdriver.

When the handle is in a horizontal position you can re-install the screws and tighten them so that the handle stays secured to the base plate. Consider applying a threadlocking solution to the threads of screws to increase grip and prevent them from loosening over time.

Drooping lever door handles could be the result of many factors. The most frequent cause is that the fixings are too tight, causing the lever bearing to pull against the door. It could also be that the levers have not been operated at the correct angle, which stretches the latch mechanism and stops it from fully springing into motion.

Another common reason is that the lever that is sprung is not working properly. This is usually due to the spring not being in the correct position within the backplate. The simplest way to check this is to turn the handle and see whether it returns to its horizontal position.

If your door handles are loose it is important to identify the issue quickly, since this can lead to excessive wear on the screws and eventually to the handle falling off of the base plate. It is also recommended to tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

The handles for doors made of upvc are also referred to as 'Snib' handle sets and feature a snib button on the top of the lever that you can push down to lock your door if you don't use a fake lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's centre and the lever or lock centre) door lock. We also carry a selection of other 68PZ door handles from manufacturers such as Ferco and Fab & Fix.

You can make your home more modern by changing your door handles whether you are replacing existing handles or installing new ones on doors you have built. There are a variety of styles of door handles made from upvc available, including traditional lever on backplate, straight or curving short latch and knob handles that resemble dummy knobs for multi point locks which are perfect for French doors.

Lever on backplate handles are typically rectangular in shape, however you can also find oval or circular versions, which are known as rose sliding door handles handles. These window handles for wooden windows for doors are identified by a lever or a knob that is mounted on the backplate. The backplate can be removed to allow for concealed fixing.

There is a variety of chrome and colored finishes available for these window handles for upvc to enhance your door and hardware, such as bolts, knobs and hinges. Some handles are equipped with a grub screw to attach the knob or lever securely to the spindle. Some handles are equipped with bathroom spindles, which can be used for bathroom locks. They also come with a thumbturn release mechanism and can be used on doors for bathrooms.

Mortise

The tubular latch is the most likely to be the culprit when your door handle made of uPVC is slammed shut. It could be due to various reasons however the most frequent is an absence of lubrication within the latch plate. This can be resolved easily by opening the door and spraying lubricant on the handle and lock. It could also be that the latch has come loose from the backplate. This is a more complex issue that requires the assistance of a specialist.

A multipoint door handle system is a great solution to solve the issue of a sticking door handle. The handles are positioned through the faceplate, and are operated with a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles are available in a number of sizes that will fit various kinds of uPVC doors. They are also available with a variety of attractive finishes that match the hardware you already have. The handles are available online or from a local locksmith. They are easy to install and come with clear directions.

You'll have to know your PZ size of your cylinder in order to choose the correct replacement handle set. This is the distance in millimetres between the inner edge of the frame of the door and the centre of the hole for the handle. You'll also require the type of lock for your door, whether it's a mortise lock or a hook lock. The most effective way to locate the right handles after you have the measurements is to use the filter for brands on the website. This will help narrow down your options, and then you'll be able to select the right size.

A typical set of handles includes a handle unit, two screws of different lengths, drill guides and instructions for installation. Smart versions, like the Igloohome Smart Mortise 2+ include a mortice lock with keypad. These are more complex devices and are best suited for professionals who install them or competent DIYers. Some handle sets include many accessories, like weather strips, which can be used to improve the appearance of the door.