• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first protection is your door lock. It will stop unauthorized access to your home. The signs of wear and tear, as well as instances like moving into a new house or burglaries, could trigger the need to replace your lock replacement upvc door.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you buy the lock that is right for you.

Deadbolt

If you want to make sure your door is secure against intruders, it's a good idea to install deadbolts. The bolt extends into the strike plate that is on the doorframe when it is locked, making it much more difficult for a burglar to break in through the door. A single-cylinder deadbolt can be activated using a key on the outside and the thumb-turn mechanism situated inside. Deadbolts can only function when it is properly installed.

First, you'll need to find out if the door has a hole for deadbolts, or if it requires drilling. Using the template that comes with the lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, use the tape measure to determine how high the deadbolt should be. Then, mark the height on the edge of the door. You can then use the speed square to draw a straight line across the mark you made for the bolt hole.

Then, use a drill to bore this area until the hole is on the other side of the door. This could take a bit of time. Sand the hole and the patio door locks replacement edge to smooth it. It's also a good idea to paint or stain the door at this point.

Remove any visible screws from the deadbolt. This will reveal both the front and rear assemblies of the deadbolt and its internal bolt. Then, loosen the bolt and replace it with a brand new one that is compatible with the door hardware. You will need to unscrew the bolt from the setplate. After that, you will need to cut out the space for the strike plate on the door frame.

If your strike plate is not in alignment it could be because the previous installer did not mortise it correctly or a weatherstripping changed the strike's position. To correct this issue, you will need to remortise the strike plate and the deadbolt. Once you have completed this check the deadbolt by closing and locking it. Make sure that the bolt is extending into the strike plate then test the key to make sure it opens and closes effortlessly.

Knob

It can make your business and home less secure if the door knob is worn. It could make it difficult to open or close the door, which is why it's an ideal idea to replace door lock (www.cheaperseeker.com) it. It shouldn't take more than 30 minutes. Use pliers or a screwdriver to take off any knobs or handles. Be cautious not to harm other components of the door.

Before you start you'll need to spray WD-40 or another dry lubricant onto the mechanism of the door knob. This will assist the new lock slide smoothly when you turn it. To ensure proper operation it is important to select a knob and handle that are compatible with your doors. If you don't have a matching doorknob and handle, you'll need to purchase a replacement.

Before you begin the replacement process, take a look at the knob that was previously used to determine which screws are holding it in place. If there are no screws, you can use the screwdriver to wedge the cover plate in between the screws plate hidden behind it.

After you have removed the knob, inspect it for indications of damage and rust. You'll have to scrub it off if you notice any marks or dents however, you shouldn't need to do anything if the knob is in good condition.

Install the new knob. First, examine the new knobs to ensure that you're choosing the right one for your door. You'll want to pick one with an extending rod that's designed to lock into the rod mechanism of the second knob. After you've inserted the new knob into the hole then slide it into the latch.

Test the spring by pressing it down repeatedly. The latch should pop up every time. Then, you can install the new knob and connect it with the rod mechanism on the first knob. Thread the long screws from the interior doorknob through the cylinder holes on the outside knob and secure it in place.

Latch

A latch is a metal piece that extends out into the doorjamb to keep it closed. It is operated by a handle or knob on the inside of the door or by a thumb turn on the exterior side of the door lock replacement. A deadbolt is a device used to secure a latch and keep intruders from breaking through the glass of the door. It can also guard against intentional or accidental closing by children or animals. It is possible to install a latch with either a single-cylinder or double-cylinder deadbolt based on the level of security.

Installing a latch requires the same steps as installing a deadbolt, but there are a few differences. First, determine the setback of the doorjamb using a tape measure to be sure the new lock will fit. The setback is measured from the edge of the doorjamb up to the middle of the hole for the latch plate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a larger setback, you might need to purchase a longer latch from a hardware shop or locksmith.

Then, make a hole for a latch plate in the doorjamb's edge. Utilize a chisel to make the mortise for the latch. Make sure that the depth is sufficient for the faceplate to be in line with the doorjamb. Tape the strike plate in place to make sure it's placed correctly.

If the strike is too high, you could kick the door in or apply pressure with the tire iron or crowbar. This can also cause the doorjamb to crack. This can be repaired by drilling a new hole in the doorjamb and then removing the core from the hole that was previously made.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate into the existing screwholes. Utilize wood putty to fill in any old bolt holes or screw holes which aren't going to be used. After the putty has dried you can sand it down to give it a professional results.

Strike

The piece of metal that is inserted between the deadbolt and latch when the door is shut is an electric strike. It is a vital component of the overall security of a lock since it helps keep the door shut and provides extra resistance to kicking or force applied to the door. If a door has been equipped with an electric strike, it can only be opened with a key or the control unit which controls its electrical impulses.

In the past, putting in an electronic strike required cutting off a part of a doorjamb in order to remove the latchbolt on a cylindrical lock from the pocket that is inside the strike. This modification is not just unattractive however, it also exposes the mechanism for the latchbolt and keeper to unauthorized users.

Recently, a number of electric strike manufacturers have come up with a "No Cut" type of strike that does not require a cutout in order to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike is fitted with an internal ramp that raises the latchbolt and keeper whenever it receives an indication from an individual reader. The retracting of the keeper and latchbolt pushes them up higher on the ramp, thereby locking the door. When the door is closed the deadbolt remains in at a lower position and the latchbolt retracts into the keeper.

Installing an electronic strike is a simple procedure, especially if you're replacing an existing strike. If you are upgrading an existing access control system to an electric strike, it is important to make sure that the new system is compatible. It is also necessary to ensure that the strike is properly connected to your access-control system and set up to function in a safe manner.

Upgrade your strike plates to heavy duty strike plates to block unauthorized entry. These plates can be fitted with up to six screws of three inches instead of two screws of three-fourths of an inch. These screws are longer, making it difficult for people to break the frame and then reach inside to turn the thumb turn part of a single cylinder deadbolt.