• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

When a pool starts leaking, the first instinct is often to call a professional and brace for a costly repair bill. In many cases, however, the problem can be identified and fixed on the spot with a few common household items and a little know‑how. Whether it’s a slow drip, a sudden gush, or an unseen seep, these quick fixes can save you time, money, and a lot of frustration.

1. Pinpoint the origin

The most important step is to locate the leak.

A slow, steady drip often comes from a broken or loose pipe, a cracked tile, or a faulty gasket.

A sudden gush may point to a broken line or a damaged pump seal.

To pinpoint the leak:

Use a bucket of water and pour it over the suspected spot. If the level falls, you’ve located the leak.

With a flashlight and a long pole, check hard‑to‑reach spots such as the pool zum aufstellen winterfest wall edge or the inside of the diving board.

Check the pool’s plumbing lines, especially the water line, return jets, and the filtration system. A quick visual inspection of the fittings can reveal a loose or cracked joint

2. Temporary fix for a cracked tile

A cracked tile or a broken pool cover can drain water for days.

Pick up a plastic bag, a rubber or silicone strip, and a metal or plastic clamp.

Slice the bag to fit the crack, position it over the broken area, and clamp it in place.

This creates a watertight seal that will keep the pool from losing water until a permanent repair can be made.

The bag also protects the crack from further damage and makes it easier to replace the tile later.

3. Secure a loose or broken gasket

Many pool equipment units—such as the skimmer, the waterline, or the pump—use rubber gaskets to seal connections.

A worn or popped-out gasket allows water to seep.

To repair:

Disable the water supply and drain the unit being repaired.

Remove the old gasket and clean the fitting surface with a mild detergent or a vinegar solution.

Put on a thin layer of silicone sealant onto the gasket and the fitting.

Put the gasket back in, ensuring it lies evenly in its groove.

Tighten the fittings to the manufacturer’s recommended torque, but don’t over‑tighten as this can damage the gasket further.

4. Fix a leaking valve or fitting

A leaking valve or pipe fitting is usually the result of corrosion or a loose joint.

If you have a pipe repair clamp, you can use it to create a temporary patch:

Place the clamp over the leaking area and tighten snugly.

For added protection, apply a layer of plumber’s putty or pipe sealant around the joint before tightening.

If the leak persists, replace the fitting in full; hardware stores usually stock many fittings compatible with standard pool plumbing.

5. Apply a waterproof sealant to a small crack

When a small crack appears in the pool shell or concrete floor, a rapid solution is to use a waterproof epoxy or polyurethane sealant.

Clean the crack with a brush and a solvent such as isopropyl alcohol.

After it dries, spread the sealant and smooth with a putty knife.

Give it time to cure as specified by the manufacturer, usually 24 hours, before refilling the pool.

6. Address a dripping pool cover

A dripping pool cover usually points to a tear or a seam that has split.

To temporarily fix it, coat the seam with rubber or silicone sealant.

If the tear is large, use a heavy‑grade adhesive tape designed for outdoor use.

This will hold the cover in place until you can replace it with a new one.

7. Examine the filtration system

A filtration system leak can result in continuous water drainage.

Inspect the filter housing, the return jets, and the suction line for cracks or loose connections.

Secure all connections, swap out damaged parts, and make sure the filter media is clean and correctly seated.

When the filter is clogged, backpressure may cause a leak at the pump’s suction line.

8. Monitor the water level

After you’ve performed a quick fix, fill the pool back up and monitor the water level over the next 24 to 48 hours.

Should the water level drop again, re‑examine the repair site.

A persistent leak may require a professional inspection or a more permanent solution.

9. Employ leak‑detection dye

If you can’t locate the leak, use a leak‑detection dye.

Scoop a little dye into the water close to the suspected spot.

The dye travels down the leak path and displays a bright streak indicating where water is escaping.

After spotting the streak, you’ll pinpoint the leak’s origin and implement the suitable fix.

10. Recognize when to call a professional

While these quick fixes can stop most minor leaks, some problems are beyond DIY repair:

A cracked pool shell or a structural crack in the concrete.

A damaged pump or filter needing replacement parts.

A leak that persists after multiple repair attempts.

A plumbing problem involving several components that is complex.

A licensed pool contractor can carry out a comprehensive inspection, use specialized tools, and apply lasting solutions that keep your pool leak‑free for years.

Conclusion

A pool leak need not translate into an expensive repair.

A methodical approach—finding the source, employing appropriate materials, and applying the correct fix—often stops the leak in its tracks.

Keep a small repair kit on hand, stay alert to changes in your water level, and don’t hesitate to call in a professional if the problem persists.

These quick fixes will keep your pool pristine and your wallet content