• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About Boarding Up a Door

Boarding up a door is one way to protect vacant investment properties from the elements. It's not a guarantee against all damage however it can help to prevent some of the problems associated with severe storms.

The boarding up a doorway of doors and windows will also deter trespassers and vandals. However, it can be expensive and time-consuming to install plywood boards over the openings in a home.

Take a measurement of the door

You'll first need a tape measure. You may want to keep a ladder or chair nearby in case you need to see more clearly the top of the frame. Wear gloves and safety glasses if you have to use these tools.

Once you have the measuring tool, start by taking the door width measurement. This can be done by running a tape measure horizontally along the door. Be sure to eliminate any extra door parts such as the door sweep and door sweep, from the measurement. Next, determine the height measurement by measuring from the floor to the sill plate or lintel. It is important to measure multiple locations, especially with older doors, because they may not be a perfect rectangle. If the measurements vary, use the largest figure.

After you've logged the width and height measurements then you'll have to determine what size boarding up service you'll need to fit into the frame. It should be at least 2 inches wider and 1'' taller than the door. 2'' higher. This will give you enough room to shim both the door and frame to fit.

When you're ready to take the door frame's width and height measurements It's recommended to remove any trim or casing the door jambs, so you can see the studs behind them. This will allow you to determine the exact dimensions of the gap between studs and the edge of the frame.

Once you've removed the trim, you can measure the width of the door frame by running the tape across the entire frame in three places and using the smallest measurement to determine the width of your door. Also, you should determine the height of the frame from top to bottom on both sides, and use the most compact measurement to determine the height of your door.

If you're having difficulty with these measurements It's a good idea to speak with an expert and have them come to your home to do the measuring for you. They will tell you what dimensions and what kind of door you need and how to prepare your frame for a replacement door.

Cut the Plywood

A door frame is typically composed of studs or thin boards that create an open space around the door. The typical door is secured by two hinges that are fixed to the studs. This means that if you want to refinish the door, it is necessary to remove the door from its hinges for a night. To prevent insects from entering your home and to secure the door opening, a simple method for boarding up service near me the door is to put plywood in the opening. It is simple to do this without the need to nail or screw the plywood to the frame of the door.

Plywood is affordable, simple to work with and looks great when it is completed. This makes it the ideal material for temporary solutions to problems that require the removal of an existing door while refinishing or installing a new one. It can also be used to protect the opening of a space being renovated, such as the construction site or basement.

Start by measuring the width of the door opening and its height. Mark the dimensions on the plywood with an utility knife and a drywall square or another metal straight edge. Next, snap the chalk lines across all the marked lines to indicate where you need to cut. Utilize a circular saw to cut the plywood to the desired size.

It is essential to protect your ears and eyes while cutting plywood. If you can wear protective goggles and earplugs while working. Additionally, it is essential to choose a blade with a lot of teeth that can cut quickly and with minimal tear-out. Make use of a small piece wood to guide the blade. Hold it a hair's width away from the marked line when cutting.

Attaching a pair of shorter braces at each end is a great method to hold the plywood in place, without screwing it into the studs. Set one brace on the inside and the other on the outside of the door. Install a deck screw in each hole and tighten using an open-end ratchet.

Fix the Plywood

When you have a piece of plywood cut to the right size and with holes for the door frame's stiles and rails predrilled and ready to attach the panel to the frame. This is a simple project that doesn't require a lot of advanced carpentry skills if you have the right tools and follow the correct procedure.

Set up a table near the doorway with two sawhorses on each end and framing lumber 2x4s. Lay the entire sheet of plywood flat atop the sawhorses and use the marks made during the measurement process as a reference to cut. Score the lines with the help of a utility knife, a drywall square or any other metal straight edge. This will act as a guide to the saw blade and will prevent splintering of the plywood when you cut it.

Put on eye protection and cut along the lines of scoring with a circular saw or table saw with a fine-tooth blade. Sand the edges of the panel using 120-grit paper to smooth it out and remove any burrs. After sanding the plywood apply a wood sealer and let it dry according to the instructions of the manufacturer.

Install the hinges on the door frame. If you're using a T-hinge, make holes in the exterior face of your door for the straps of the hinges. Then, place the hinge's outside on its mark and attach it onto the frame using a screw gun. Repeat the procedure for each hinge on the interior of your door. Be cautious not to tighten them too much or the door may shift.

If you're using a single outside T-hinged door, you can make it easier to close and lock using a chain latch by putting a piece of wire through the loops on the hinges on the outside. Fold a short piece to tie wire in half, and then fish it through the two holes on the exterior of the door. Then twist the wires to secure the door.

Install the Plywood

Install the plywood in the door's opening according to the measurements you have taken. Move the frame's header (top) and the sill. Utilize a level to make sure there's not any slop in the header or sill. If the level isn't perfect you can put another shim in the place where you need it and repeat the procedure until you've got the sill and the header to be plumb.

Once the plywood has been put in place, secure it using the stainless-steel hinge bolts and wingnuts. It's a good idea make use of a screw gun with an hex-head attachment so that you prevent stripping the head of the screws.

While you're at it If your home was constructed with studs running across the width of your doorway make holes for hanger bolts in the plywood and into each framing stud. This is a much easier job than making the hole with a drill or drywall saw.

After installing the plywood, measure the width and the height of the door opening. If needed, trim the bottom of the plywood to fit the height of your door frame. Cut two pieces of framing wood 1-by-6 to form braces for the upper and lower ends. Cut along the lines marked on your plywood using a circular blade with fine-toothed teeth. Wear eye protection. Get rid of any splinters that may have formed in the cuts with a Sanding block.

After you have placed the braces, use two pairs of 2-inch finishing nail to attach each brace to the plywood. Once you're done, counter sink the heads of all nails. Make sure to seal the braces and the plywood with a good wood sealer, such as this wipe-on polyurethane from Minwax.

If the door is too large You can either put in decorative molding to fill the space between your door and jamb or you can alter the size of your opening. In many instances, it's cheaper and more convenient to get a new door. It also removes any problems you may have had with your original door, if it was damaged or was not fit for the opening.