• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

It's a good idea you to replace your locks when they begin to exhibit signs that they're worn out. This could be due to having difficulty turning the lock, or a key that doesn't fit.

Fortunately, putting in new door lock hardware is actually very easy. All you have to do is follow these steps.

Deadbolt

The deadbolt is the door's primary defense against forced entry. It is more durable and secure than the latch that opens the lock, so you should ensure that the deadbolt you purchase is sturdy enough for your needs. If you can, choose deadbolts that are made of case hardened steel and no screw heads that are exposed on the outside to prevent unintentional drilling. The interior side of the deadbolt should also be secured to your door frame to enhance security.

During installation, make sure that the bolt on your new deadbolt is extending smoothly through the strike plate while you close and lock the doors. If not, mortise the bolt in the strike plate with a wood chisel, and then install the deadbolt. Make sure the doorknob's latch aligns with the hole in the deadbolt when you shut and lock the door, too.

Make sure whether the new deadbolt is compatible with the old one before installing it. The majority of door locks come with a template showing how far the bolt should be located above the doorknob. However, it is always best to consult an expert in hardware in case you aren't sure of the backset size you require for your doors. They will be able point you to models that are compatible with your doors and the existing deadbolt opening.

After ensuring that the new bolt assembly is of the proper length, screw it into the hole in the door. If the new deadbolt comes with a latch faceplate, screw it into the frame as well. It's an excellent idea to attach the faceplate using the recommended screws to the frame.

Some lock sets have some lock sets have a "dummy" or decorative bolt that allows you to install the keyed deadbolt and still have a working latch. If you're able to choose, the dummy bolt must be installed using the same screws that are used to install the faceplate for the latch. This will ensure maximum security.

Some deadbolts can only be opened through a thumb-turn, while others come with two cylinders that permit both keyed and unkeyed access. It is recommended to select an item that is commercial grade to ensure the highest security. They've been tested to withstand up to 250,000 cycles of closing and opening before they are sold to homeowners.

Latch

The latch is the component of the lock that retracts the bolt to open and close the door. It's usually secured by screws on the side of the lock, however it could also be fixed to the strike plate or to the inside of the french door lock replacement jamb. It is essential to replace door lock a door latch with the right one for the hardware you have. You can test this by putting the latch up to your existing hardware or look at the label of a replacement. Dunn Lumber carries a variety of brands, however it's generally best to choose the same brand of your existing hardware to ensure that you get an appropriate latch that fits perfectly.

Some doors feature an ahasp instead of a latch. A hasp is a piece of strap that has a slot in it that allows it to be placed over a staple. The staple is then attached to the door frame or door with nails. When the door is shut, the strap will pull the staple down and secures it into position. Commercial buildings utilize a hasp since it is cheaper than a lock.

Like any mechanism with moving parts, a lock can wear out from frequent use over time. Sometimes the internal mechanism will begin to "stick" and be difficult to turn, making it necessary to replace the entire lockset. Sometimes, the exterior doorknob can break and it is necessary to replace it as well.

If your lock is squeezing, you can try using some graphite inside the keyhole. You can either dust it or spray it on the key, then turn the lock a couple of times to incorporate the graphite. You can also employ a screwdriver for the removal of the knob and reveal the inside components and allow you to see what's going on inside the.

After removing the knobs then tighten the two or three setscrews at the edges of the cylinder by turning them clockwise. The faceplate must be removed and replaced. Surface-mounted rim locks come with an additional set of cylinder setscrews located on the back of the case, which must be removed, as well as the cover plate.

Strike Plate

The strike plate is a reinforcement and upgrade to the locking system. It is attached to the holes that are used for deadbolts or master key systems bolts. It wards off intruders by ensuring that the latch of the lock is held in the plate when the bolt is engaged. A top-quality strikeplate can enhance the life of locks as well as increase security.

A standard strike plate looks like a flat plate of metal with an opening or set of holes cut into it. It is secured, typically using screws, to the doorway's frame to provide the latch with a place to rest in when it is closed. The strike plate needs to be aligned precisely with the lockset to provide maximum security against burglaries.

If the strike plate of a door is damaged, you should replace it as soon as possible. This will ensure that the door will close and latch properly. To replace a strikeplate you must first ensure that it is aligned with the bolthole in the doorjamb. This can be done by placing a piece of adhesive tape over the bolt hole, and then testing the latch. If the latch doesn't catch, remove the tape. Then chisel the area to ensure that the strike plate is flush with the doorjamb.

After the area has been cut out, it is important to use a longer screw to secure the strike plate. They must be at least 3 inches in length in order to ensure they are securely fixed to a stud which is behind the trim board. If you do not install the longer screws, then the wood in the doorjamb could split during a kicking attack by a burglar, leaving the door vulnerable.

A professional locksmith can quickly replace a worn or damaged strike plate. They can also install new strike plates on doors that never had them before. In addition, they can upgrade existing strike plates to enhance a building's security and improve appearance. This could assist property owners in attracting tenants who are looking for a safer living space and peace of mind.

Keys

The key cylinder of your lock is the part that receives the key to move pins so that the inside handle can turn. The key cylinder is the most crucial part of your door lock because it fulfills the function for which locks were designed to protect your family, you, and your belongings. This is the reason that people frequently get their locks rekeyed instead of replacing door locks upvc door lock replacement door locks; Read Home Page, them.

It is more difficult to replace a lock than to simply swap out the existing handle and deadbolt. The entire lock must be replaced by taking the old cylinder and hardware from the door (including the handle when you have a knob lock combination) and putting a brand new one in its place. There are numerous DIY-friendly tools that can be used to replace a door lock. However, it's best to contact a locksmith to ensure the job is done correctly.

Before you install the new cylinder and lock it is crucial to have the right key for your home. A key that is a duplicate won't work and could even cause the lock to fail completely, making it impossible to open. A professional can prevent this by ensuring you have a working, real key for your home.

The next step is to remove the faceplate and then the latch plate. You will require an screwdriver to take out the screws which hold them in place. If the new plates will be similar to the original ones, you might want to secure them to save time. If you must replace them, be careful not to tighten the screws too much as this could affect their grip on the door.

After removing the plates, you will need to measure the new locks. It is important to know the door's dimensions before visiting the hardware store. Although a lot of locksets available can be used today to fit in a standard door's thickness, it's better to purchase them ahead of time. Be aware that doorknob locksets tend to be different sizes than deadbolt locksets. Commercial models can come with an enlarged bolt or latch.