• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Changing your door lock is a simple and inexpensive way to increase the security of your home. This process isn't for everyone. It requires some skill and perseverance.

You need to replace the cylinder, which is inside the knob's body. The cylinder recognizes the key when it is placed into the lock.

The old lock can be removed

First, remove the lock that was previously in place. This is a relatively easy procedure, but there are a few things to be aware of. Make sure the new lock fits your door. This will ensure it is secure and doesn't leave a gap in the deadbolt or latch.

After removing the latch plate, you'll be required to search for two bolts or screws on the inside of casing that hold the casing in place with the two halves of the lock. Remove them with the help of a screwdriver, and then pull the lock out of the door. If you are using a mortise locking system there is a set screw that binds the handle to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

Remove the deadbolt and latch plug from the door jamb. Then, you can put in your new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit.

You might want to change your lock for various reasons, such as when you suspect that someone else holds the key or if you have new roommates. You can save money if you remove the lock yourself, instead of hiring a professional. The process is simpler than many people imagine and can be completed in just a few minutes.

Remove the trim and handle from your door. With a flat screwdriver pry off the trim. You will be able twist off the majority of it, and in certain cases the handles may fall off completely. Then, look for a tiny hole on the interior side and insert a straightened clip into it. This will trigger the release mechanism and allow you to take the handle from the door. Then, look for a small tab that is located inside of the lock and push it with a screwdriver that is flat. Once the spindle is removed, you can remove the cylinder and housing.

Selecting a new locking system

When it comes time to pick the right lock for your home there are a lot of choices. Think about the various kinds of locks and select one that fits the style of your door. Take into consideration the backset (the distance between the edge of the door and the center of the hole for the lock) and the cross bore (small hole in the frame of the door frame). Select a lock that is suitable for the door's thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give you an idea of their durability and the difficulty to pick them or disable them. A upvc window lock repair near me grade 3 might be ideal for a peaceful apartment in the countryside, whereas replacement locks for double glazed windows that are grade 1 may be better suited to the busy streets near a storefront.

Most smart door locks require a digital key code to open. If you're concerned about hacking or other security issues seek out an expert locksmith or your local police department for assistance.

Replace the cylinder

You can easily replace damaged or broken door lock cylinder using a simple DIY project. The trick is to select the right cylinder and follow the instructions that come with it. The first step is to remove the knob or handle in the event that one is present, then unscrew the trim that is attached to the base of the lock cylinder by using a screwdriver. After the trim has been removed, you can remove the screws holding the cylinder with the flathead. The cylinder is then gently removed from the door.

Be sure to take measurements of the length of the new cylinder prior to installing it. Find the distance from the center to the left and right sides of the cylinder using the aid of a tape measure. Purchase a new cylinder which has the same measurements. This will help prevent cylinder snapping, which can occur when the door is kicked out or when the key gets stuck inside.

Insert the Upvc Replacement Window Locks cylinder in the door and then turn the key. This will ensure that the cylinder is aligned with the carrier, which is normally located on the outside of the lock. Then, you can loosen the set screw that should be a couple of turns in the head. If there is a screw at the outside of the case, which holds the door, you'll have to loosen it.

You can replace the old double glazed window lock repairs cylinder with a new one by slipping it into the case and tightening the set screws. The process of reinstalling the component that connects a cylinder with a lock indicator stem is also crucial. You can do this by pulling three small tabs in the back of the cylindrical with needle-nosed pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you need to put back in the strike plate and latch plate as well as the retaining ring that is connected to the top window lock replacements the cylinder.

Installing a new lock

Begin by measuring the width of your door if you are replacing a lock that is already in use. Most residential locksets are designed for a door thickness of 1 3/8 - 3/4 inch. If your door is thicker, you will need a thick door kit that includes longer screws as well as a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come with a thorough installation guide to help you. Read the instructions carefully before starting the process to make sure that you are following all the steps. The guide will give you an idea of how much skill is required to finish the task. You may want to seek out a friend who has had experience in changing locks for assistance if are changing locks for the first time.

Before installing the new lock it is recommended to tape over the openings of the old hardware. This will stop screws from falling through the holes and will also protect any tiles you have put in. It will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch comes with an ad-hoc strip of masking tape or gaffer tape, but you can use any tape you have.

Once you've removed the screws that hold the interior portion of the lock section to the exterior side, pull it straight away. It's crucial to do this quickly to prevent the lock from accidentally closing itself and damage the mechanism.

If your new lock is equipped with a latch bolt, fit the new bolt into its upper cross bore. Be sure to put it in the correct position, which is usually marked by an arrow on the faceplate. Then, place the latch plate onto the bolt and screw it in place.

Attach the deadbolt to the jamb on the door. Test the deadbolt by throwing it a several times to make sure that it extends all way into the strike plate and is fully secured. If you're using an electronic smart lock, be sure to follow the instructions for programming it. This involves downloading an app, registering your email address, verifying your identity, and accessing the wireless network to connect your device.