• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

If the locks on your door lock replacement near me start to begin to show signs of wear and tear, it's generally a good idea to replace the locks. These indicators include having trouble turning the lock, or having a key that doesn't fit.

The good news is that installing new door lock hardware is actually quite simple. It is all you need to do is follow these steps.

Deadbolt

The deadbolt is your door's primary defense against forced entry. It is stronger and safer than the latch that activates the lock. So, you'll be sure that the deadbolt you choose to purchase is compatible with your needs. If you can, select deadbolts made of case-hardened steel that does not have exposed screwheads on the exterior to stop drilling by anyone else. To increase security, the interior side of the deadbolt should be drilled into the door frame.

During the installation process Make sure that the new deadbolt's bolt extends smoothly into the strike plate when you lock and close the door. If it isn't, use a wood chisel to make a mortise for the bolt hole in the strike plate and then re-install the deadbolt. Make sure the doorknob's latch meets the deadbolt hole when you close and lock the door, too.

Before installing your new deadbolt, ensure whether it's the same size of the previous one. Most door locks come with a template that shows you how high above the doorknob the bolt should be. However, it's always best to consult an expert at an hardware store if you're not sure what backset measurement is suitable for your doors. They can guide you towards models that will work with your doors and the existing deadbolt opening.

After you've confirmed that your new bolt assembly is of the right length, you can screw it into the hole of the door. Screw the latch faceplate into place if your new deadbolt has one. It's also a good idea to attach the latch faceplate using the screws recommended to the frame.

Certain lock sets come with a "dummy" or decorative bolt, which allows you to install the deadbolt with a key and still have a working latch. If you have the option, the dummy bolt must be installed using the same screws that are used to mount the faceplate of the latch. This will ensure the highest security.

Some deadbolts have only a single cylinder accessible from the inside using the thumb-turn, whereas others have a double cylinder which allows keyed and unkeyed entry. No matter which kind you pick, it's a good idea to buy a commercial-grade lock for the best security. They're tested to withstand 250,000 cycles of closing and opening before being sold to homeowners.

Latch

The latch is the part that retracts the bolt when you open or close the door. It's usually held in place by screws located on the sides of the lock, but it may also be fastened to the strike plate or to the inside of the door jamb. It is crucial to replace a door latch with the correct one for your existing hardware. You can test this by holding the latch up to your existing hardware, or you can look on the label of the replacement locks for patio doors. Dunn Lumber offers a wide variety of brands. However, it's best to choose the same brand that matches the hardware you already have. This will ensure that the latch you buy will fit properly.

Certain doors come with a hasp instead of the latch. A hasp is a strap that has a slot in it to fit over staples. The staple is then fixed to the door door frame with a nail. When the door is closed the strap pulls back on the staple and locks in the frame. Commercial buildings employ a hasp since it is less expensive than a lock.

Locks can wear out over time like any other mechanism with moving parts. Sometimes the internal mechanism can "stick" or be difficult to turn. This could require the replacement of the entire lockset. Sometimes, the doorknob or handle may break, and it is necessary to replace it also.

If your lock is stuck it is possible to try using some graphite in the keyhole. You can either spray it on the key or dust it on the inside of the lock, then use the lock a few times to incorporate the graphite into the mechanism. You can also remove the knob with the help of a screwdriver. This will expose all the parts and let you see what is happening inside the.

After removing the knobs then tighten the two or three screws on the edge of the cylinder by turning them clockwise. It is also recommended to remove the faceplate and replace it. Surface-mounted rimlocks come with an additional set of cylinder screws on the back case which must be removed as well as the faceplate.

Strike Plate

The strike plate is a reinforcement and upgrade to a locking system. It is placed to the holes for deadbolts or master key systems bolts. It keeps intruders at bay by ensuring that the latch of the lock is held in the plate when the bolt is engaged. In addition to enhancing security, a good strike plate can also improve the life of locks.

Standard strike plates are flat metal plates with a hole, or several holes cut into them. It is fastened, usually using screws, to the frame of a doorway to provide the latch with a place to rest in when it closes. It is crucial that the strike plate is properly aligned with the lockset in order to ensure maximum security against break-ins.

If a door's strikeplate is damaged, it must be replaced as soon as is feasible to ensure that the door will close and latch correctly. When replacing lock on upvc door a strikeplate, you must first ensure that it is properly aligned with the bolt hole in the doorjamb. One way to check this is to put a piece of tape in the bolt hole and then test the latch by opening and closing the upvc door locks replacement. If the latch doesn't catch, you must remove the tape and then chisel the area to ensure that the strike plate will be flush with the doorjamb.

Once the area is cut out, it is important to use a more powerful screw to anchor the strike plate. The screws should be at minimum three inches long to ensure that they are securely secured to a stud behind the trim board. If you don't use the longer screws, the doorjamb's wooden frame could split during a kickin attack by a burglar, making the door vulnerable.

A professional locksmith can quickly replace a strike plate that has become worn or damaged. They can also install new strike plates on doors that never had them before. They can also modify existing strikeplates to enhance the security of a building as well as its appearance. This will help property owners draw in tenants looking for a safe living environment and peace of mind.

Keys

The key cylinder is a part of your lock that takes a particular key that allows pins to be moved into position so that the internal handle can be turned. The key cylinder is the primary component of your door lock, since it serves the purpose for which locks were created to safeguard your family, you, and your possessions. It is for this reason that people often have their locks rekeyed instead of being replaced.

The procedure of replacing lock in Upvc door a lock is more complex than simply replacing the existing deadbolt or handle lock. The entire lock must be replaced by taking the old cylinder and hardware from the door (including the handle if you have a knob-lock combo) and installing a new one in its place. There are a variety of DIY-friendly kits that can be used to replace a door lock. However, it's recommended to speak with a locksmith to ensure the job is done correctly.

Before you install the new cylinder and lock, it is important to have the right key for your home. A duplicate key will not perform as expected and could cause the lock's failure and make it impossible for you to open. A skilled professional can assist you in avoiding this by making sure that you have a working, genuine key for your home.

The next step is to take off the faceplate and latch plate. You will require a screwdriver for the removal of the screws that secure them. You may want to leave them in place if new plates are similar to the originals. This will save you time. If you have to replace them, Replacing lock in upvc door don't overtighten screws, as this can cause them to lose their grip.

After removing the plates you will need measure for the new locks. Although many modern locksets will be able to fit a standard width of door, it is best to know the dimensions of your door in advance to avoid any confusion when you go to the hardware store. Doorknob locksets can be different sizes from deadbolt locks commercial models might have a bigger bolt or latch.