• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your first security measure against unauthorized entry into your home. Locks may require replacement patio door lock due to wear and tear or other circumstances such as moving into a new house or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you buy the lock that is right for you.

Deadbolt

Installing a deadbolt is great way to secure your door from intruders. When the bolt is extended into the strike plate of the doorframe, it makes it more difficult for an intruder to break through the door. A single-cylinder deadbolt can be activated with a key on the outside and a thumb-turn piece that is located inside. Deadbolts can only function when it is properly installed.

You will first need to determine whether the door already has an existing hole for a deadbolt, or if you have to bore it out. Mark the position of the hole for the deadbolt on the surface of the door Replace door lock using the template included with your lock installation set. Then, use your tape measure to determine the height the deadbolt should be. Mark this measurement on the door's edge, and then use the speedsquare to draw a straight line across the mark you made for the bolthole.

Then using an electric drill, bore through the hole until it reaches the opposite side of the door. It may take a while. Sand the hole and the edge of the door to smooth it. At this point, it's a good idea to stain or paint your door.

When the door is in place take off any screws visible on the deadbolt. This will reveal the front and back assembly of the deadbolt, and also the bolt inside. Then, unscrew the bolt and replace door lock (Recommended Reading) it with a new one that is compatible with the door hardware. You'll need to remove the bolt from the setplate. Once this is done, you will need to chisel the area for the strike plate that is on the door frame.

If your strike plate is misaligned It's likely that the previous installer didn't mortise it correctly or a weatherstripping popped up and changed the strike position. It is necessary to re-mortise the strikeplate and perhaps even the deadbolt to fix the issue. Once you have completed this, test the deadbolt by closing it and locking it. Make sure that the bolt extends into the strike plate then test the key to make sure it closes and opens smoothly.

Knob

It could make your home and business less secure if the door knob is damaged. It can make opening or closing the door more difficult, which is why it's an ideal idea to replace the knob. It shouldn't take longer than 30 minutes. You can use a screwdriver and pliers to take off the old knob or handle Be careful not to harm any other parts on the door.

Spray WD-40, or a different dry lubricant on the mechanism of your door knob prior to you begin. This will help the new lock slide smoothly when you turn it. It is essential to choose an excellent knob and handle that match the doors you currently have to ensure that the lock is operating properly. If you don't have a matching doorknob, you will need to purchase a replacement.

To begin the replacement door lock process, first look at the knob or handle to see the screws that hold it in place. If there aren't any screws, Replace door lock you can make use of a screwdriver and wedge it between the cover plate and the plate with hidden screws and then remove it.

After taking the knob off, inspect it for indications of damage and rust. You'll have to scrub it up if there are any scratches or dents however you don't need to do anything if the knob is in good condition.

Install the new knob. You should first examine the two knobs in order to make sure that you've chosen the right one for the door. You'll need to choose one with an extended rod that is interlocked with the rod mechanism of the second knob. Once you've put the new knob in the hole in the door and then carefully place it in the latch.

Thread the latch plate screws downwards, then test the spring by pushing down repeatedly. The latch should spring back up each time. Then, put in the new knob and interlock it with the rod mechanism of the first knob. Thread the long screws from the doorknob's interior through the cylinder holes on the exterior knob, and fix it in its place.

Latch

A latch is a piece of metal that extends through the door jamb to keep it closed. The latch is operated via a knob or handle on the inside of the door, or by a thumb-turn on the outside. A deadbolt is a device used to secure a latch and stop intruders from breaking through the glass of the door. It also offers protection from the accidental or deliberate closing of the door by children or pets. The latch can be fitted using a single cylinder deadbolt or double cylinder deadbolts, based on the level of security you prefer.

Installing a deadbolt is exactly the same as installing a latch, however there are some differences. First, determine the setback of the doorjamb using a tape measure to make sure that the new lock will fit. The setback is measured from the edge of doorjamb up to the center of hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is higher, you may need to purchase a latch that is larger from a hardware or locksmith store.

Next, drill a hole for the latch plate in the doorjamb's edge. Use a chisel for chiseling out the mortise of the latch and ensure it's deep enough for the faceplate of the new latch to be close to the doorjamb. Place the strike plate in place to make sure it's in the right position.

If the strike is too high, you can push the door back or apply pressure using an iron tire or crowbar. This can cause cracks to the doorjamb. This can be repaired by drilling a new hole through the doorjamb, then removing the core from the previous one.

The final step is to install the new strike plate, which can be accomplished by screwing it in place over the existing screw holes. Utilize wood putty to fill in any existing holes for screws or bolts that won't be used. Once the putty has dried you can sand it until it has an even finish.

Strike

The piece of metal that is inserted between the deadbolt and latch when the door is closed is an electric strike. It is a vital component of a lock's overall security, because it keeps the door shut and also provides additional resistance to force or kicking applied to the door. If a door comes with an electronic strike, it will be opened only with a key and the control unit that regulates the electrical impulses.

In the past, installing an electronic strike was as simple as cutting a piece of a doorjamb to release the latchbolt of a cylindrical lock from the pocket inside the strike. This change can be an inconvenience when it comes to the aesthetics of an opening as well as exposing the keeper mechanism and latchbolt to unintentional users.

Recently, several electric strike manufacturers have developed a brand new electric strike called the "No Cut" strike that doesn't need cutouts in the doorjamb for operation. They use a specific design that allows the latchbolt and keeper to slide into the pocket without damaging the doorjamb's faceplate.

The strike is fitted with an internal ramp which lifts the latchbolt and keeper when it receives a signal from a reader. The retracting of the keeper and latchbolt raises them on the ramp, which locks the door. When the door is closed, the deadbolt remains in place and the latchbolt retracts in the keeper.

Installing an electric strike is an easy process, particularly if you are replacing lock in upvc door the strike on a previous door. If you're upgrading an access control system to an electric strike, you must make sure that the new system is compatible. It is also necessary to ensure that the strike is properly connected to your access-control system and is set up to operate in a safe manner.

Upgrade your strike plates with heavy duty strike plates to prevent unauthorised entry. These plates are fitted with four to six screws of three inches instead of the two three-fourth inch screws typically used in regular strikes. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.