• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace door lock Door Locks

Your first protection is your door lock. It will prevent unauthorized access into your home. The signs of wear and tear and even instances such as moving into a new home or burglaries, could trigger the necessity of replacing your lock.

To begin, determine the size of your cylinder by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will assist you purchase the right-sized lock.

Deadbolt

Installing a deadbolt can be a great way to secure your door against intruders. The bolt extends into the strike plate on the doorframe when it is locked, making it much more difficult for burglars to break in through the door. A single-cylinder deadbolt can be activated by a key located on the exterior and a thumb-turn piece situated inside. A deadbolt will only work if it is installed correctly.

It is first necessary to determine whether the door already has an existing hole for a deadbolt or if you'll need to drill it. Using the template that comes with the lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, you can use your tape measure to determine how high the deadbolt should be. Mark this measurement on the door's edge. Use a speedsquare to draw a straight line across the mark you made for the bolt hole.

Then, use a drill to bore this spot until the hole is on the other side of the door. This may take a while. Then, sand down the hole and the edge of the door until it is smooth. At this moment, it's a good idea to paint or stain your door.

Remove any screws that are visible from the deadbolt. This will reveal both the front and rear assemblies of the deadbolt as well as its bolt inside. Then, remove the bolt and replace lock on upvc door it with a brand new one that matches your door hardware. It is necessary to remove the bolt from a setplate. After this, you'll need to chisel the area on the door frame to accommodate the strike plate.

If your strike plate isn't aligned properly it's likely that the previous installer didn't properly mortise it or a weatherstripping popped up and altered the strike position. To fix this problem, you will need to remortise both the strike plate as well as the deadbolt. Close and lock the deadbolt after you have completed this step. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

When a door Replace door Lock knob is worn out it could make your business or home less secure. It could also make opening and closing the door more difficult, which is why it is recommended to replace upvc door lock the knob. It shouldn't take you longer than 30 minutes. You can use a screwdriver or pliers to take off the knob or handle that was previously used, but be careful not to damage any other parts on the door.

Before you start you'll need to spray WD-40 or some other dry lubricant on the mechanism of the knob for your door. This will let the lock to move smoothly when you turn it. To ensure proper operation it is essential to select the knob and handle that match the doors you already have. If you don't have a doorknob that is compatible and handle, you'll need to purchase a replacement.

Before you begin the replacement patio door lock process, take a look at the knob that was previously used to determine what screws are keeping it in place. If there aren't screws, you can use the screwdriver to wedge the cover plate in between the screws plate hidden behind it.

Once you've removed the old knob, examine it for signs of damage or rust. If the knob is damaged or has dents or marks then you'll need to clean it. Otherwise it shouldn't require any major work.

It's time to install the new one. First, examine the two new knobs to ensure you're picking out the right one for your door. You'll need to choose one that has an extending rod that is designed to lock with the rod mechanism on the second knob. After you've placed the new knob in the hole and then put it in the latch.

Thread the latch plate screws downwards, then test the spring by pushing down several times. The latch should then spring back up each time. Then, you can install the new knob and lock it to the rod mechanism on the first knob. Thread in the other long screws from the interior knob through the hole for the cylinder on the exterior doorknob and lock it in place.

Latch

A latch is a steel piece that extends into the doorjamb in order to hold it shut. The latch can be operated by a knob or handle on the interior of the door, or a thumb-turn on the outside. A deadbolt can be used to secure a latch and stop intruders from breaking through the glass of the door. It also offers protection from accidental or intentional closing of the door by pets or children. You can install the latch using either a single-cylinder deadbolt or double-cylinder deadbolt, depending on the level you prefer for security.

Installing a deadbolt is the same as installing a latch, but there are some differences. First, measure the setback of the doorjamb using an instrument to make sure the new lock will fit. The setback is the distance between the edge of the doorjamb to the middle of the hole for the faceplate of the latch. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is greater, you may need to purchase a latch that is larger from a hardware or locksmith store.

Then, you'll need to drill a hole for the latch plate into the edge of the doorjamb. Use a chisel and cut the mortise of the latch. Make sure that the depth is enough for the faceplate to be flush with the doorjamb. Tape the strikeplate in place to ensure it's placed correctly.

If the strike is too high, you could knock the door down or apply pressure with an iron tire or crowbar. This can also crack the doorjamb. To remedy this, the strike could be reduced by drilling a second hole in the doorjamb and chiseling out the center of the previous hole.

The last step is to put in the new strike plate which can be accomplished by screwing it in place over the existing screw holes. Use wood putty then to fill in any old holes for screws or bolts which aren't going to be used. Once the putty is dry then sand it to a smooth finish for a professional finish.

Strike

The metal piece that engages the deadbolt and latch when the door is closed is an electric strike. It is a vital component of the security of a lock, since it helps keep the door shut and provides extra resistance to force or kicks applied to the door. If a door is fitted with an electronic strike, it will be opened by using an entry key and a control unit that regulates the electrical impulses.

In the past, putting in an electronic strike required cutting a portion of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket that is inside the strike. This is an issue in regards to the appearance of an opening as well as exposing the latchbolt and keeper mechanism to unintentional users.

Recently, a variety of electric strike manufacturers have created a "No Cut" kind of strike that doesn't require a cutout for operation. The strikes use a unique design to allow the keeper and latchbolt to slide into the strike pocket without marring the faceplate of the doorjamb.

The strike is equipped with an internal ramp that raises the latchbolt and keeper when it receives an indication from an individual reader. The latchbolt and keeper are pushed higher up the ramp by the retraction. When the door is closed the deadbolt remains in extended and the latchbolt is retracted into the keeper.

Installing an electric strike is an easy task, especially if you are replacing an existing strike door. If you're upgrading an existing access control system to an electric strike, replace Door lock you must ensure that your new system is compatible. Also, you must make sure that the strike is properly connected to your access control system and is configured to function in a safe manner.

One way to protect against unauthorized access is to upgrade the strike on your doors to a heavy-duty strike plate. These plates use four to six three-inch screws instead of the two, three-fourth inch screws typically employed in regular strikes. These longer screws make it difficult for people to break the frame and then reach inside to turn the thumb turn part of a single deadbolt cylinder.