• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

If the locks on your door start to exhibit signs of wear and tear it's recommended to replace them. These indicators include having trouble turning the lock, or having a key that doesn't fit.

It is simple to install new door hardware. All you have to do is follow these steps.

Deadbolt

The deadbolt is the primary protection of your door against forced entry. It is stronger and more secure than the latch that activates the lock. So, you'll be sure that the new deadbolt you purchase meets your needs. If you can, choose deadbolts that are made of case hardened steel and has no exposed screw heads on the outside to prevent unintentional drilling. The interior side of the deadbolt needs to be inserted into the door frame to improve security.

During the installation, ensure that the bolt on the new deadbolt slides smoothly through the strike plate when you close and lock the doors. If it doesn't then use a chisel made of wood to mortise the bolt hole in the strike plate, and then re-install the deadbolt. Make sure that the doorknob's latch is in contact with the hole for the deadbolt when you lock and close the door, too.

Before installing your new deadbolt, check that it is the same size of the previous one. The majority of door locks include an illustration of how to replace upvc door lock high the bolt should be above the doorknob. However, it is always best to consult an expert in hardware in case you aren't sure of the backset measurement you need for your doors. They can guide you in the direction of models that are compatible with your door and the existing deadbolt opening.

Install the bolt assembly into the door hole after ensuring it's the right length. Screw the faceplate of the latch into place if your new deadbolt is equipped with one. It is a good idea to attach the latch faceplate to the frame using the recommended screws in addition.

Some lock sets include the option of a "dummy" or decorative bolt, which allows you to install the keyed deadbolt and still have a working latch. If you have this option the dummy bolt must be installed with the same screws as the faceplate of the latch, [Redirect Only] and it's important to ensure that both bolts fit correctly to ensure maximum security.

Some deadbolts can only be opened via a thumb-turn from inside some have two cylinders that allow keys and non-keyed access. It is recommended to select a lock that is commercial grade to ensure the highest security. They've been tested to withstand 250,000 cycles of closing and opening before being sold to homeowners.

Latch

The latch is the part of the lock that retracts the bolt to open and close the door. It is typically secured by screws on the sides but it could also be attached to the strike plate of the door jamb. It's important that you replace patio door lock the door latch with the correct one for the hardware you have. You can either hold the latch up against the hardware you have already installed or look up the label on a replacement door locks. Dunn Lumber offers a wide range of brands. However, it is best to choose the same brand that matches your existing hardware. This will ensure that the latch you purchase will fit correctly.

Some doors have the appearance of a hasp, instead of latch. A hasp consists of an elastic strap with a slot punched in it, which fits over the staple. The staple is then fixed to the door frame or door using a nail. When the door is closed the strap pulls down on the staple and locks into the position. Commercial buildings utilize a hasp since it is cheaper than a lock.

Locks wear out over time, just like any other mechanism with moving parts. Sometimes, the internal mechanism may begin to "stick" and become difficult to turn, requiring cost to replace upvc door lock mechanism replace the entire lockset. Sometimes the exterior doorknob will fail and it is essential to replace it as well.

If your lock is sticking, you can try using some graphite in the keyhole. You can either squirt some on the key or sprinkle it onto the inside of the lock. Then operate the lock a few times to work the graphite into the mechanism. You can also make use of a screwdriver to take off the knob and reveal the internal components and let you see what's happening inside.

After taking the knobs off then tighten the three or two setscrews on the outside of the cylinder by turning them clockwise. The faceplate should be removed and replaced. Surface-mounted rimlocks also have an additional set of cylinder screws on the back case which must be removed along with the faceplate.

Strike Plate

The strike plate, which is fixed to the door frame, above the holes to accommodate the deadbolt or master key bolt system, strengthens and upgrades the locking mechanism. It keeps intruders at bay by ensuring that the latch of the lock is held in the plate when the bolt is engaged. A strikeplate that is of high-quality can improve the longevity of locks and enhance security.

A standard strike plate appears like a flat plate of metal with a hole or set of holes cut into it. It is affixed to the door frame usually with screws, which gives the latch something to sink into when it closes. It is crucial that the strike plate be carefully aligned with the lockset to ensure maximum security against break-ins.

If the strike plate on the door is damaged you must replace it as soon as possible. This will ensure that the door can close and latch properly. The first step to replace the strike plate is to ensure that it is aligned correctly with the bolt hole inside the doorjamb. This can be accomplished by placing a piece adhesive tape over the bolt hole, and then attempting to test the latch. If the latch does not catch then take off the tape. Then chisel the area to make the strike plate level with the doorjamb.

After the area has been chiseled it is essential to use a longer bolt to secure the strike plate. They should be at least 3 inches long in order to ensure they are anchored securely into a stud which is behind the trim board. If you don't install the screws that are longer or the wood inside the doorjamb could split in the event of a kick-in attack by a burglar and leave the door vulnerable.

A professional locksmith will swiftly replace a damaged or worn out strike plate. They can also install a new strike plate on the door that hasn't had one before. They can also modify existing strikeplates to enhance the security of a building as well as its aesthetics. This could aid property owners in attracting tenants who want a safer living space and peace of mind.

Keys

The key cylinder is a part of your lock that takes a particular key that allows pins to be moved into place so that the inner handle can be turned. The key cylinder is the most crucial component of your door lock since it serves the purpose for which locks were created to safeguard you, your family members, and your belongings. Rekeying locks is a economical option than replacing them.

The process of replacing patio door lock the lock is more complicated than simply replacing the existing handle-lock combo or deadbolt. The entire lock must be replaced by removal of the old cylinder as well as hardware from the door (including the handle if you have a knob-lock combo) and installing a new one in its place. While there are a number of DIY-friendly tools that can be used to replace a lock on your own, it is recommended that you contact a skilled locksmith to make sure the job is done properly.

Before you install the new cylinder and lock it is crucial to have the correct key for your home. A duplicate key will not function properly and may even cause the lock to fail which makes it impossible for you to open. A professional with experience can assist you in avoiding this by making sure you have a genuine, functional key for your home.

Next, you will need to take off the faceplate and latch plate. You will need a screwdriver to remove the screws which hold them in place. You might want to keep them in place if new plates are similar to the originals. This will cut down on time. If you need to replace upvc door lock mechanism them, be careful not to tighten the screws too much since this can affect their grip on the door.

After you have removed the plates, you will have to determine the proper measurement to determine the proper size of the lock. It is essential to know the dimensions of your door prior to visiting the hardware store. Although many locksets are designed to fit in a standard door's thickness, it's better to purchase them ahead of time. Doorknob locksets are often different sizes than deadbolt locks and commercial models may have a larger latch or bolt.