• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

Whether you're replacing your handles or adding a little extra security, you'll find the right handle for your door. These upvc handles are easy to fit and comply with the required 92mm centres of multipoint locks.

The backplate fixing center and the lever/keyhole dimensions are the most important measurements. Compare these measurements carefully with your existing measurements prior to placing an order.

Lever/Pad

Lever pad door handles are made up of the lever handle on one side and a paddle shaped handle on the other. They are designed to work with key wind locks however they can also be used to split spindle multipoint door locks (though you'll need a separate dual spindle lock case).

Our selection of upvc handle lever pads are available in a wide range of finishes. They will be shown in the drop-down list after you have selected the perfect handle for your doors. Some styles of handles are not available in all finishes. It is recommended to check the technical drawing and dimensions for the item you are looking to ensure that you get the right fit and size.

It is crucial to ensure that when you choose a new set of Upvc lever pad handles, they are in line with the PZ (distance from the spindle of the handle to the center of the hole in the cylinder) of your multipoint door locks. This is because they need to be aligned in order for the doors to stay locked, regardless of whether you are looking at them from the outside or inside. The handles we sell are designed to work with the majority of standard cylinder locks, but you should double-check prior to ordering.

You will need to remove your handles that you have already installed and then dismantle the lock case if you are upgrading to dual spindle handle levers since this will require an additional split cylinder inline. These are available separately and we have the complete technical diagram for you to examine in the images for each product.

Once you have removed the screws that hold your existing door handle it is an ideal idea to loosen them and inspect the mechanism to determine the condition it is in. You may need to loosen the screws further when they aren't tight. Then you can take off the old handle and spindle and replace it with a new door handle made of upvc window locking handles. Before putting the handle in place it is recommended to check that it is in the right position, and you can do this by placing your finger in the gap between the door frame and the handle to make sure it is in a level position.

Lever/Lever

Lever door handles are a multi point lock using the Euro cylinder and are found on the majority of upvc double doors, aluminium doors, and some wooden doors. They are available in two varieties, with an interior lever and a paddle on the outside. Sprung - They have an internal spring cassette within the backplate that helps bring the handle lever to a horizontal position. Non-sprung - These do not have a spring mechanism, and will require manual pulled to bring the handle lever to the horizontal position.

To repair a sagging door handle lever you'll need to locate the hole or pin that is the detent access point. It's typically an insignificant hole or protruding ring or rectangular found on the handle base plate. Once located you can loosen the set screw with a screwdriver and remove it to release the lever and return it to the horizontal position.

Once the handle is in a horizontal orientation, you can put the screws back in place and tighten them so that the handle is secure on the base plate. You should also consider applying a threadlocking adhesive solution to the screw threads to improve the grip and stop them from loosing over time.

There are a variety of reasons that door handles for levers slide. The most common cause is that the fixings aren't tight which causes the lever bearing to pull against the door. It could also be because the levers aren't being operated in a straight line and this is compressing the latch mechanism, preventing it from fully springing back into service.

A common cause of a spring lever not operating properly is the spring not being in the proper position on the backplate. To check if the handle returns to horizontal, simply move it.

If the door handles aren't tight, it is essential to spot the issue fast, as this can lead to excessive wear on the screws, and even to the handle falling off the base plate. It is also recommended to tighten any loose screws regularly to prevent them from becoming looser.

Lever/Snib

The handles for doors made of upvc are also referred to as handle sets with a 'Snib' and have a snib lever on the top of the lever that you can push down to lock your door if you don't have an dummy lock. These handles come with a Fullex lock 68PZ. (68mm between the spindle and lock centre). We also stock a variety of other 68PZ door replacement uPVC door handles handles from manufacturers such as Ferco and Fab & Fix.

Changing your door handle is an inexpensive method to upgrade your home, whether you're replacing your handles or installing new ones to doors you've constructed in your home. There are a variety of styles of door handles made from upvc available, including traditional lever on backplates, straight or curved short latches, and knob handles with dummy handles for multi-point locks, which are ideal for French doors.

Rose door handles are circular or oval-shaped versions of lever on backplate handles. These handles for doors are identified by a lever or a knob that is attached to the backplate. The backplate is removable for concealed fixing.

The uvpc window handles are available in a variety of finishes including coloured and chrome finishes to match your door and other hardware like knobs, hinges and bolts. Some handles have a an grub screw that can be used to connect the knob or lever securely to the spindle. Some handles are equipped with bathroom spindles that can be used for bathroom locks. They also come with an release mechanism that turns the thumb and can be used on doors for bathrooms.

Mortise

If your uPVC front door handle is stuck in the open position, the reason is likely to be due to the tubular latch. It could be due to a number of things, but the most common is the lack of lubrication on the latch plate. It is possible to fix this issue by opening the door, spraying lubricant on the handle and lock. It could also be that the latch has slipped away from the backplate. This could be more of a problem and will require a specialist to repair.

A multipoint handle is the ideal solution to stuck door handles. These handles mount through the faceplate of the door and are operated with an actuated thumb turn knob or key which activates an electronic cam that locks the deadbolt. The handles are available in different sizes to suit different kinds of uPVC door, and come in various attractive finishes that are compatible with the hardware that is currently in use. The handles can be purchased on the internet or through an authorized locksmith in your area. They are simple to install, with clear instructions.

You'll need to know your PZ cylinder's size to choose the correct replacement window handle handle set. This is the distance from the edge of the inner frame of the door to the center point of the hole for the handle in millimetres. It is also important to be aware of whether your door has hook-style locks or a mortise lock. The most effective way to locate the correct handle once you know the measurements is to use the filter for brands on the website. This will narrow down the options and you can then choose the right size from there.

A typical set of handles includes the handle unit, a pair of different length screws as well as drill guides and installation instructions. The smart models, like the Igloohome Smart Mortise 2+ includes an entire mortice lock that has built-in keypad. These are more complex models and are ideal for professionals who install them or adept DIYers. Some handle sets include many accessories, such as weather strips, which can be used to improve the appearance of the door.