• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace lock on patio door Door Locks

Door locks are your primary line of defense against unauthorized access to your home. Locks may need to be replaced because of signs of wear and tear, or other situations such as moving into a new home or a break-in.

To begin, determine the size of your cylinder using the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will allow you to purchase the appropriate lock.

Deadbolt

If you want to ensure your door is secure against burglars, it's a good idea to install a deadbolt. The bolt extends into the strike plate on the doorframe when it is locked, making it more difficult for burglars to gain entry through the door. A single-cylinder deadbolt can be activated using a key on the outside and the thumb-turn mechanism located on the interior. Deadbolts will only work when it is properly installed.

First, you'll need to determine if the door has a hole for deadbolts or requires drilling. Mark the position of the hole for the deadbolt on top of the door using the template included with your lock installation set. Then, use your tape measure to determine how high the deadbolt should be. Then, mark the height on the side of the door and use a speed square to draw a straight line across the mark you made for the bolt hole.

Then using a power drill, bore through the hole until it is on the opposite side of the door. This could take a bit of time. Sand replace door Lock the hole and the edge of the door to make it smooth. It's also an excellent idea to stain or paint the door at this point.

Once the door is ready, remove any screws that are visible on the existing deadbolt. This will reveal the front and rear assembly of the deadbolt and its internal bolt. Then unscrew the old bolt and replace upvc door lock mechanism door lock (click through the next website page) it with an alternative bolt that matches your door hardware. The bolt is often connected to a set plate which you'll have to remove. After that, you'll have to chisel the area on the door frame to accommodate the strike plate.

If your strike plate is out of alignment, it could be because the previous installer didn't mortise it properly, or a weatherstripping has changed the strike's position. To fix this problem, you will need to remortise the strike plate as well as the deadbolt. After this is done check the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

When a door knob wears out, it can make your home or business less secure. It may make it more difficult to open or close the door, so it's recommended to replace it. It shouldn't take more than 30 minutes. Use pliers or a screwdriver to remove any old knobs or handles. Be cautious not to harm other parts of the door.

Before you begin you'll need to spray WD-40 or another dry lubricant onto the mechanism of the knob for your door. This will assist the new lock move smoothly when you turn it. To ensure that it operates properly, it's important to choose the right knob and handle to are compatible with your doors. If you don't have a doorknob that matches then you'll have to buy a replacement.

Before you begin replacing upvc door locks the knob, look over the knob you replaced to determine what screws are that are holding it in place. If there aren't any screws you can use a screwdriver to insert between the cover plate and the plate with hidden screws and remove it.

After removing the old knob examine it for evidence of damage or rust. You'll need to clean it off if you notice any marks or dents however, you shouldn't need to do anything major if the knob is in good shape.

Install the new knob. You should first examine the two knobs to ensure that you've selected the right one for the door. You'll need to choose one with an extender rod that will interlock with the rod mechanism of the second knob. After you've placed the new knob in the door's hole carefully place it in the latch.

Thread the latch plate screws down and test the spring by pressing down several times. The latch should spring back up each time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob into the cylinder holes on the outside knob and fix it in the knob's position.

Latch

A latch is a metal piece that extends out into the doorjamb to secure it closed. The latch can be operated by a knob or handle on the inside of the door, or a thumb-turn on the exterior. A latch can be secured using a deadbolt to keep intrusions from piercing the glass of the door. It also provides protection from accidental or intentional closing of the door by pets or children. A latch can be installed with one cylinder deadbolt or double cylinder deadbolts, based on the level of security you prefer.

Installing a deadbolt is the same as installing a latch, replace door Lock but there are some differences. First, measure the setback of the doorjamb with an instrument to make sure the new lock will fit. The setback is measured from the edge of the doorjamb all the way to the center of hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If you have a greater setback, you may need to purchase a larger latch at a hardware store or locksmith.

The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Utilize a chisel to chisel the latch mortise. Make sure the depth is enough for the faceplate to be flush with the doorjamb. Tape the strikeplate in place to ensure it's placed properly.

If the strike is placed too high, the door could be kicked in or pressure imposed on it using a crowbar, or tire iron. This can cause cracks to the doorjamb. To correct this, the strike can be lowered by drilling another hole in the doorjamb and cutting out the core of the hole that was previously drilled.

Installing the new strike plate is the last step. This can be done by screwing the new plate over the existing screw holes. Then apply wood putty to fill in the screw holes that were previously used and the bolt hole that is not used. After the putty has dried, sand it smooth for an elegant finish.

Strike

An electric strike is the metallic piece that holds the latch and deadbolt engage when the door is closed. It is a vital part of the lock's overall security, as it prevents the door from opening and gives an additional barrier to force or kicking. If a door is fitted with an electronic strike, it can be opened only with a key and the control unit that regulates its electrical impulses.

Traditionally the installation of an electric strike required cutting a section of the doorjamb to release a cylindrical lock's latchbolt from the pocket in the strike. This change can be an issue when it comes to the appearance of openings and also exposes the latchbolt and keeper mechanism to unintentional users.

Recently, several electric strike manufacturers have developed an innovative type of electric strike called the "No Cut" strike that doesn't require cutouts in the doorjamb to operate. These strikes utilize a special design that allows the keeper and latchbolt to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that raises the latchbolt and keeper whenever it receives an electrical impulse from a controller or reader. The latchbolt and keeper are pushed higher up the ramp by the retraction. When the door is shut, the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electronic strike is a simple process, particularly if you're replacing an existing strike. If you are upgrading an access control system to an electric strike, you need to make sure that the new system is compatible. Also, you must ensure that the strike is connected to your access control system and is set up to function in a fail-safe manner.

Upgrade your strike plates with heavy duty strike plates to stop unauthorized entry. These plates use up to six screws of three inches instead of the usual two screws of three-fourths of an inch. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single deadbolt cylinder more difficult.