• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace a lock on a upvc door to Replace Door Locks

Door locks are the first protection against unauthorised entry into your home. Locks might require replacement because of signs of wear and tear or other circumstances like moving into a new home or a break-in.

To begin, determine your cylinder size by measuring the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will assist you select the appropriate lock.

Deadbolt

Installing a deadbolt is a great way to secure your door from burglars. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for replace Door lock an intruder through the door. A single-cylinder deadbolt can be activated by a key located on the exterior, and a thumb-turn device located on the interior. A deadbolt will only work if it's installed correctly, though.

It is first necessary to determine if the upvc door lock replacements has a hole that is suitable for a deadbolt or if you have to bore it out. With the template included with your lock installation kit, mark the location of the hole for the deadbolt on the door's surface. Then, you can use your tape measure to determine the height the deadbolt should be. Mark this high point on the door's edge and use speedsquares to draw a straightline across the mark you made for the bolt hole.

Then, use a power drill to bore this spot until the hole reaches the opposite side of the door. This may take a while. Sand the hole and edge of the door to smooth it. It's also an excellent idea to paint or stain the door at this point.

When the door is open, remove any screws visible on the existing deadbolt. This will reveal the front and rear assembly of the deadbolt and its internal bolt. Then, remove the bolt and replace door Lock it with a brand new one that is compatible with your door hardware. The bolt is often connected to a setplate, which you will need to unscrew. After that it is time to cut out the space for the strike plate on the door frame.

If your strike plate is out of alignment It could be due to the previous installer did not mortise it properly, or a weatherstripping changed the strike's position. It is necessary to re-mortise the strikeplate and possibly even the deadbolt itself to correct this problem. Once this is completed check the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

It could make your business and home less secure if the door knob is worn. It can make opening or closing the door more difficult, so it's recommended to replace it. Replacing a knob is a relatively simple DIY project that shouldn't take less than 30 minutes to complete. Make use of pliers or a screwdriver to remove any old knobs or handles. Be careful not to harm the other components of the door.

Spray WD-40, or a different dry lubricant, onto the mechanism of your door knob before you begin. This will allow the lock to move smoothly when you turn it. To ensure that it operates properly, it's important to choose a knob and handle that match the doors you already have. If you don't already have a doorknob that matches and handle, you'll need to purchase a new one.

To begin the replacement process, look over the knob or handle to see what screws hold it in place. If there aren't any screws you can use a screwdriver to wedge between the cover plate and the hidden screws plate and remove it.

After removing the old knob examine it for evidence of damage or rust. It's important to clean it up if there are any scratches or dents however you don't need to do anything when the knob is in good condition.

Install the new knob. It is important to first look over the two knobs in order to make sure that you are choosing the appropriate one for your door lock replacement. You'll need to select one with an extending rod that will interlock with the rod mechanism of the other knob. After you've placed the new knob into the hole, slide it into the latch.

Thread the latch plate screws downwards and test the spring by pressing down repeatedly. The latch should then spring back up every time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob into the holes for cylinders on the outside knob and lock it into the knob's position.

Latch

A latch is a steel piece that extends out into the doorjamb in order to hold it shut. It is operated by a handle or knob on the interior side of the door or a thumb turn on the exterior side of the door. A latch can be secured with deadbolts to prevent intrusions from piercing the glass of the upvc door replacement lock. It can also protect against the accidental or deliberate closing by animals or children. It is possible to install an entry point with either a single-cylinder or double-cylinder deadbolt, depending on the level of security.

Installing a latch follows the same steps like installing a deadbolt but there are a few differences. To ensure that the new lock will work first, determine the setback of the doorjamb with the tape measure. The setback is the distance between the edge of the doorjamb to the center of the hole for the latch faceplate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is higher than that, you might need to purchase a latch that is longer from a locksmith or hardware store.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Use a chisel to chisel out the mortise of the latch and ensure it's deep enough for the faceplate of the new latch to be close to the doorjamb. Tape the strikeplate to the doorjamb to ensure it's placed correctly.

If the strike is too high, you can knock the door down or apply pressure with a tire iron or crowbar. This can also crack the doorjamb. This can be fixed by drilling a new hole into the doorjamb, and cutting the core from the previous one.

Installing the new strike plate is the final step. This can be done by screwing the new plate over the screw holes that are already in place. Then, use wood putty to cover the holes from the previous screws and the bolt hole that is not used. After the putty has dried then sand it to a smooth finish for a professional finish.

Strike

The piece of metal that is inserted between the latch and deadbolt when the door is closed is an electric strike. It is an essential component of the lock's security because it stops the door from opening, and also provides additional resistance to force or kicking. If a door is equipped with an electronic strike, it will be opened only by an entry key and a control unit that regulates its electrical impulses.

Traditionally, installing an electric strike involved cutting out a portion of the doorjamb in order to remotely remove a cylindrical lock's latchbolt from the pocket within the strike. This change can be a drawback in terms of the aesthetics of an opening as well as exposing the mechanism of the latchbolt and keeper to unintentional users.

Recently, several electric strikes manufacturers have come up with a "No Cut" kind of strike that does not require a cutout for operation. They use a specific design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper when it receives an electrical signal from a reader or controller. The retracting of the keeper and latchbolt causes them to rise on the ramp, locking the door. When the door is closed, the deadbolt stays extended and the latchbolt is retracted into the keeper.

Installing an electric strike is a simple process, especially in the case of replacing the strike on a previous door. If you're upgrading an existing access control system to an electric strike, it is important to ensure that your new system is compatible. Also, replace Door lock you must ensure that the strike is properly connected to your access control system and that it is designed to operate in a fail-safe manner.

One way to safeguard against access by unauthorized persons is to upgrade the strike on your doors to a robust strike plate. These plates use four to six three-inch screws instead of the two, three-fourth inch screws that are typically used in standard strikes. These longer screws make breaking the frame to reach the thumb turn piece on a single deadbolt cylinder more difficult.