• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up commercial property boarding up companies a Door

The protection of vacant investment properties from the elements is possible by putting boarding up commercial property a door with a board. It's not a guarantee against all damage however it can help to avoid certain problems that come with severe storms.

Boarding up windows and doors can also deter trespassers and vandals as well as squatters. Installing plywood boards over openings can be costly and time-consuming.

Take a measurement of the door

The first thing you'll require is tape measure. You might also want to have a ladder or chair handy for when you need to gain a better view at the top of the frame. Wear gloves and safety glasses when you use these tools.

Begin by measuring the width of the door. You can do this by running an x-ray measure horizontally across the door. Make sure to remove any extra parts of the door, for instance a sweep, before measuring. Then, measure the height by measuring up from the floor to the sill plate or the lintel. It is crucial to measure more than one location especially for older doors, Boarding up windows and doors because they may not be a perfect rectangle. If the measurements differ then use the largest number.

You'll have to determine the size of the frame after you've determined the length and width. It should be at minimum 2'' wider and 1'' taller than the door. 2'' higher. This will give you plenty of room to shim the frame and door to fit.

When you're ready to take the door frame's width and height measurements It's a good idea to remove any trim or casing from around the door jambs so you can see the studs behind them. This will let you take measurements of the exact gap between the frame's studs and the edge.

After taking off the trim, take a measurement of the width of your door frame using a tape measure. The frame should be measured at three different locations and use the smallest measurement. Also, you should take a measurement of the height of the frame from top to the bottom on both sides, and use the shortest measurement to determine the height of your door.

If you're having difficulty with the measurements, get a professional to your home and do the measuring. They'll be able give you the exact kind of door and size you require and how to prepare the frame for the door you want to buy.

Plywood can be cut into pieces

A door frame is typically composed of thin boards or studs that create an open space around the door. The typical door is secured by two hinges that are connected to the studs. If you wish to restore a door, you will have to take it off its hinges and then leave it for a night. Placing plywood into the door opening is a simple method to enclose the door and keep insects from gaining entry into the home. It is easy to do this without having to nail or screw the plywood onto the door's frame.

Plywood is cheap, easy to work with, and looks fantastic when finished. It is the perfect material to use as a temporary solution for situations where you have to take down an existing door to refinish or install the new one. It can also be used to protect the opening of a room that is being renovated, such as the construction site or basement.

Begin by measuring the width of your door opening and its height. Mark the measurements with an utility knife and a metal straight edge such as a drywall or a metal square. Then, snap an outline of chalk across each line to indicate where you want to cut. Finally, use circular saws to cut out the plywood to size.

It is essential to protect both your ears and eyes while cutting plywood. If possible, wear a pair of safety goggles and earplugs when working. In addition, it's crucial to use a knife that has a wide range of teeth that cut quickly and with less tear-out. To minimize the chance of cutting pieces of wood from the edges of your cut using a small piece of wood as an example to guide the blade and hold it at a distance of just a hair's width away from the line when cutting.

Attaching a pair of shorter braces at each end is a great method to hold the plywood in place, without screwing it into studs. Set one brace side that is inside and the other one on the outside of the door. Then, position two 1-1/2-inch deck screws into each of the holes, and tighten them with an open-end wrench.

Fix the Plywood

It's time to join the panel to the frame after you have the wood sheet cut to the right size and the holes for the rails and stiles of the door frame predrilled. It is a fairly easy project that doesn't require any extensive carpentry skills as long as you follow the correct procedure and use the proper tools.

Start by setting emergency boarding up service a table near the doorway with two sawhorses and a 2-by-4 frame lumber at each end of the table. Lay the entire sheet of plywood flat atop the sawhorses, using the marks from the measurement process as a reference to cut. Utilize a utility knife and a straight edge made of metal to score the lines. This will create an outline for the saw blade, and will help keep the wood from splintering when cutting the plywood.

Wear eye protection and use a circular table saw with a blade that has a fine-toothed edge to cut along the score line. Sand the edges of the panel with 120-grit paper to smooth it out and eliminate any burrs. After sanding the plywood then apply a wood sealer and allow it to dry according to the manufacturer's instructions.

Install the hinges on the frame of the door. If you're using a hinge with a T-hinge make holes in the exterior side of your door to accommodate the straps of the hinges. Then, you can screw the hinge's outside edge to the frame with the screwdriver. Repeat the procedure for each hinge on the interior of your door. Be cautious not to tighten them too much, or the door may shift.

If you have a single T-hinged outside door, you can make it easier for the latch to close by placing a wire through the loops of the exterior hinges. Bend a small piece of tie wire in half and place it through the two holes on the outside of the door. You can then twist the wires together to tighten them and secure the door.

Install the Plywood

Install the plywood in the door's opening according to the measurements you made. Move the header (top) of the frame and the sill (bottom). Use a level to make sure there's no slop in the header or sill. If it's not quite right, put another shim where you need it and repeat the procedure until you've got the sill and the header to be level.

Once the plywood is in the frame, fix it using stainless steel hinge bolts and wing nuts. It's a good idea to utilize a screw gun that has an hex-head attachment so that you avoid stripping the head of the screws.

While you're there, if your house was built with studs that extend the height of your doorway make holes for hanger bolts in the plywood and into the framing studs. This is a lot easier than using a drywall cutting tool to make the hole.

After you have installed the plywood, measure the width and the height of the door opening. If needed, trim the plywood bottom to be a little higher than the height of your door frame. Cut two pieces of framing lumber 1 by 6 to serve as braces for the upper and lower edges. Cut along the lines marked on your plywood with a circular blade with fine-toothed teeth. Wear eye protection. Get rid of any splinters that may have formed in the cuts using the help of a the sanding block.

After you have the braces set, nail each one to the plywood with pairs of finishing nails that measure 2 inches. Once you're done counter-sink the heads of all nails. Seal the braces with a good wood sealing product, like the wipe-on polyurethane from Minwax.

If the door is still too big for your doorway, you could add an ornamental molding to fill in the gap between the jamb and the door or you can resize the opening. In most instances, however it is less expensive and simpler to purchase a new door. It also eliminates any issues that you might have experienced with your original door in the event that it was damaged or not suitable for the opening.