• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace lock on patio door Door Locks

The first line of defense is your door lock. It can stop unauthorised access into your home. Locks may require replacement because of signs of wear and tear, or other situations like moving into a new home or a burglary.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to purchase the correct-sized lock.

Deadbolt

Installing a deadbolt is great way to secure your door against intruders. The bolt extends into the strike plate that is on the doorframe when locked, making it much more difficult for burglars to gain entry into the door. A single-cylinder deadbolt can be activated by a key located on the exterior, and a thumb-turn piece that is located inside. Deadbolts are only effective if it's installed correctly however.

You will first need to find out if the door has a hole that is suitable for a deadbolt, or if you need to drill it out. Mark the location of the hole for the deadbolt on top of the door using the template included with your lock installation set. Use a tape measure to determine the height of the deadbolt. Then, mark the height on the edge of the door. You can then use the speed square to draw an even line across the mark you made for the bolt hole.

Then, use a drill to bore out this area until the hole reaches the opposite side of the door. It may take a while. Then, sand the hole and the edges of the door so that it's smooth. At this moment, it's a good idea to stain or paint your door.

When the door is open remove any screws visible on the existing deadbolt. This will reveal the front and back assembly of the deadbolt as well as the bolt that is inside. Then unscrew the old bolt and Replace door Lock replace it by the new bolt to match your door hardware. The bolt is usually connected to a set plate which you'll need to unbolt. After this, you'll need to chisel the door frame to accommodate the strike plate.

If your strike plate is not in alignment It could be due to the previous installer failed to mortise it properly, or an installation of a weatherstripping altered the strike position. You'll need to re-mortise your strike plate and perhaps even the deadbolt to correct this problem. Close and lock the deadbolt when you have completed this step. Be sure the bolt is extending into the strike plate and then test the key to ensure it opens and closes easily.

Knob

It could make your business and home less secure If the knob on your door is damaged. It can also make it harder to open or close the door, so it's a good idea to Replace door lock the knob. It shouldn't take you longer than 30 minutes. You can use a screwdriver as well as pliers to get rid of the knob or handle that was previously used, but be careful not to damage any other parts on the door.

Before you begin, you'll want to spray WD-40 or a different dry lubricant on the mechanism of the knob for your door. This will allow the new lock slide smoothly when you turn it. To ensure proper operation it is important to select the right knob and handle to match your existing doors. If you don't already have a matching doorknob then you'll have to purchase a new one.

Before you begin replacing lock on upvc door the knob, take a look at the knob that was previously used to determine which screws are that are holding it in place. If there aren't any screws you can make use of a screwdriver and Replace Door Lock wedge it between the cover plate and the plate with hidden screws and pop it off.

After removing the old knob, inspect it for evidence of damage or rust. If the knob has any scratches or marks, you'll have clean it. Otherwise it shouldn't need any major work.

Now is the time to put in the new one. It is important to first look over the two knobs in order to make sure that you've selected the right one for the door. You should select one with an extended rod that's designed to lock into the rod mechanism of the second knob. Once you've positioned the new knob over the hole in the door and then carefully insert it into the latch.

Thread the latch plate screws down and test the spring by pressing down on it several times. The latch should spring up every time. Install the second knob and lock it to the rod mechanism of the first knob. Thread the long screws of the interior doorknob into the holes for cylinders on the outside knob and lock it into its place.

Latch

A latch is a steel piece that extends out into the doorjamb to secure it closed. The latch is operated via a knob or handle located inside the door, or by a thumb-turn on the exterior. The latch can be secured with a deadbolt to keep thieves from breaking through the glass. It also offers protection from the accidental or deliberate closing of the door by pets or children. A latch can be set with a single cylinder deadbolt or a double cylinder deadbolt, according to the security level you prefer.

Installing a latch requires the same steps as installing a deadbolt, but there are a few variations. First, measure the setback of the doorjamb using a tape measure to be sure that the new lock will fit. The setback is measured from the edge of doorjamb up to the center of hole for the latch plate. The standard setback is 2 3/8 to 2. 3/4 inches. If your setback is larger it is possible to purchase a latch that is larger from a locksmith or hardware store.

The next step is to drill an edge bore hole in the doorjamb for the latch plate. Use a chisel and make the mortise for the latch. Make sure the depth is enough to allow the faceplate to be in line with the doorjamb. Place the strike plate in place to make sure it's in the right position.

If the strike is set too high, the door can be kicked in or pressure imposed on it using a crowbar, or tire iron. This can also cause the doorjamb's to crack. This can be corrected by drilling a new hole through the doorjamb, then chiseling the core out of the old one.

Installing the new strike plate is the final step. This can be done by fixing the new plate to the screw holes that are already in place. Utilize wood putty to fill in any existing bolt holes or screw holes which aren't going to be used. After the putty has dried, sand it to a smooth finish.

Strike

An electric strike is the metallic piece where the latch and deadbolt engage when the door is shut. It is an essential component of the lock's security, as it prevents the door from opening and gives an additional barrier to force or kicking. If a door has been equipped with an electric strike, it can be opened using keys or the control unit that controls its electrical impulses.

In the past, installing an electronic strike required cutting a piece of a doorjamb, which would release the latchbolt of a cylindrical lock from the pocket inside the strike. This change can be a drawback in regards to the appearance of an opening and also exposes the mechanism of the latchbolt and keeper to unauthorized users.

Recently, a number of electric strike manufacturers have created a new type of electric strike, dubbed the "No Cut" strike that doesn't require an opening in the doorjamb to operate. These strikes utilize a special design to allow the latchbolt and keeper to slide into the strike pocket without damaging the doorjamb faceplate.

The strike has an internal ramp which lifts the latchbolt as well as the keeper when it receives a signal from a reader. The retracting of the keeper as well as latchbolt pushes them up higher on the ramp, locking the upvc door replacement lock. When the door is closed the deadbolt remains in at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike is a simple process, especially when you are replacing a strike on an existing door. If you are upgrading an existing access control system to an electric strike, it is important to make sure that the new system is compatible. It is also necessary to make sure that the strike is properly wired to your access control system and that it is designed to operate in a fail-safe manner.

One method to guard against intrusions by thieves is to upgrade the strike on your doors to a heavy-duty strike plate. These plates are fitted with four to six three-inch screws instead of the two three-fourth inch screws commonly used in regular strikes. These longer screws make breaking the frame to reach the thumb turn piece on a single deadbolt cylinder more difficult.