• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace upvc door lock to Replace door lock (imoodle.win) Door Locks

The first line of defense is your door lock. It will prevent unauthorized entry to your home. Locks might require replacement door lock due to signs of wear and tear or other events such as moving into a new residence or a burglary.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to buy the lock that is right for you.

Deadbolt

If you want to make sure your door is secure against criminals, it's a great idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe, it makes it more difficult for an intruder to break through the door. A single-cylinder deadbolt can be activated using a key on the outside and a thumb-turn piece situated inside. Deadbolts can only function only if it is correctly installed.

The first step is to determine if the door has a hole to install deadbolts, or if it has to be bored. Utilizing the template included with the lock installation kit mark the spot of the deadbolt's hole on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Mark this high point on the door's edge, and then use speedsquares to draw a straight line across the mark that you made to mark the bolt hole.

Then, use a drill to bore out this area until the hole reaches the opposite side of the door. This may take some time. Then, sand the hole and the edges of the door so that it is smooth. It's also recommended to stain or paint the door at this point.

Remove any visible screws from the deadbolt. This will reveal the front and back assembly of the deadbolt, and also the bolt inside. Then, unscrew the bolt and replace it with a brand new one that is compatible with the door hardware. The bolt is often connected to a setplate that you need to unbolt. Then, you'll need to chisel the door frame for the strike plate.

If your strike plate is out of alignment, it could be because the previous installer didn't mortise it correctly or an installation of a weatherstripping altered the strike position. To fix this problem, you will need to remortise both the strike plate and the deadbolt. After this is done Test the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

If the knob on your door is worn out it could make your business or home less secure. It could make it more difficult to open or close the door, making it recommended to replace it. Replacing knobs is an easy DIY task that should not take longer than 30 minutes to complete. Use a screwdriver or pliers to take off any knobs or handles. Be careful not to harm other parts of the door.

Spray WD-40, or another dry lubricant on the mechanism of your door Replace door lock knob before you begin. This will let the lock to move effortlessly as you turn it. To ensure proper operation it is essential to select the right knob and handle to match your existing doors. If there's no match, you'll need to buy an additional doorknob and latch plate.

Before you begin the replacement process, take a look at the knob that was previously used to determine what screws are that are holding it in place. If there aren't any screws, you can use a screwdriver to insert between the cover plate and the hidden screws plate and then remove it.

After taking the knob off, inspect it for indications of damage and rust. You'll need to clean it off if there are any scratches or marks however, you shouldn't need to do anything when the knob is in good condition.

Now it's time to install the new one. Before you do that, look over the knobs you've chosen to ensure that you're selecting the correct one for your door. You'll want to pick one with an extending rod designed to interlock with the second knob's rod mechanism. Once you've positioned the new knob over the door's hole, carefully place it in the latch.

Thread the latch plate screws down, then test the spring by pushing down on it repeatedly. The latch should rise every time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws from the interior doorknob into the holes for cylinders on the exterior knob and secure it in place.

Latch

A latch is a metallic piece that extends into the doorjamb to secure it closed. It is operated with a knob or handle on the inside of the door, or a thumb turn on the outside side of the door. The latch can be secured with deadbolts to prevent thieves from breaking through the glass of the door. It also offers protection from the accidental or deliberate closing of the door by pets or children. The latch can be fitted using single cylinder deadbolts or double glazed door lock replacement cylinder deadbolts, depending on the security level you prefer.

Installing a latch involves the same steps similar to installing a deadbolt however, there are a few distinctions. To ensure that the new lock will fit, first measure the setback on the doorjamb with a tape measure. The setback is measured from the edge of the doorjamb all the way to the center of hole for the latch plate. A standard setback is 2 3/8 to 2 3/4 inches. If you have a larger setback, you may have to purchase a longer latch from a hardware store or locksmith.

Then, make a hole for a latch plate at the edge of the doorjamb. Use a chisel to chisel out the mortise for the latch and ensure it's deep enough to allow the faceplate of the new latch to be close to the doorjamb. Tape the strikeplate to the doorjamb to ensure that it's positioned correctly.

If the strike is too high, you can knock the door down or apply pressure using an iron tire or crowbar. This can cause the doorjamb to break. This can be fixed by drilling a new hole through the doorjamb and then chiseling the core out of the previous one.

The final step is to mount the new strike plate, which is done by screwing it in place over the existing screw holes. Then you can use wood putty to fill in the old screw holes and the bolt hole that won't be used. After the putty is dry then sand it to a smooth finish.

Strike

The piece of metal that is inserted between the deadbolt and latch when the door is closed is an electric strike. It is a vital component of a lock's overall security, since it seals the door and provides extra resistance to force or kicks applied to the door. If a door comes with an electronic strike, it will be opened only by a key and the control unit that regulates its electrical impulses.

In the past, putting in an electronic strike was as simple as cutting off a part of a doorjamb, which would release the latchbolt of a cylindrical lock from the pocket within the strike. This is an inconvenience when it comes to the aesthetics of an opening as well as exposing the keeper mechanism and latchbolt to any unauthorised users.

Recently, several electric strikes manufacturers have developed a "No Cut" type of strike that does not require a cutout in order to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike is fitted with an internal ramp that lifts the latchbolt and keeper when it receives a signal from an individual reader. The latchbolt and keeper are lifted higher up the ramp by the retraction. When the door is closed, the deadbolt remains retracted, and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward procedure, especially when you're replacing an older strike. However, if you're upgrading to an electric strike for an access control system, you'll need to make sure your new system is compatible with the type of lock you have installed. It is also necessary to ensure that the strike is properly connected to your access control system and is configured for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to prevent the entry of unauthorized persons. The plates utilize four to six screws of three inches instead of the two, three-fourth inch screws that are typically employed in regular strikes. The longer screws make it harder for people to break the frame and reach inside to turn the thumb turn piece of a single deadbolt cylinder.