• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your first protection against unauthorised access to your home. Signs of wear and tear and even instances such as moving into a new house or burglaries, could trigger the necessity of replacing your lock.

To begin, you must determine your cylinder size by measuring the distance between the adjustment screw and the center of the cylinder knob. This measurement will help you purchase the right-sized lock.

Deadbolt

Installing a deadbolt can be a excellent way to protect your door from intruders. The bolt extends into the strike plate that is on the door frame when it's locked, making it more difficult for burglars to gain entry into the door. A single cylinder deadbolt can be activated with keys on the exterior side and a thumb turn piece on the interior. A deadbolt will only work if it is installed correctly.

First, you must determine whether the door already has a hole that is suitable for a deadbolt or if you have to drill it. Mark the location of the hole for the deadbolt on the exterior of the door using the template included with your lock installation kit. Then, use the tape measure to determine the height the deadbolt needs to be. Then, mark this height on the edge of the replacement upvc door locking mechanism. You can then use the speed square to draw an even line across the mark you made for the bolt hole.

Then by using the power drill, drill out the hole until it is on the opposite side of the upvc door lock replacement. This could take a bit of time. Then, sand down the hole and along the edge of the door so that it is smooth. At this stage, it's a great idea to paint or stain your composite door lock replacement.

Remove any visible screws from the deadbolt. This will reveal both the front and rear assembly of the deadbolt, as well as its internal bolt. Then, unscrew the bolt and replace it with a brand new one that is compatible with the door hardware. It is necessary to remove the bolt from the setplate. After this is done it is time to chisel the area for the strike plate that is on the door frame.

If your strike plate isn't aligned properly, it's likely because the previous installer didn't properly mortise it or a weatherstripping was installed and changed the strike position. It is necessary to re-mortise the strikeplate and perhaps even the deadbolt to correct this problem. Close and lock the deadbolt once you have completed this step. Make sure that the bolt extends into the strike plate and then test the key to make sure it opens and replace door Lock closes easily.

Knob

If the knob on your door wears out it could make your home or business less secure. It may also make it harder to open or close the door, making it a good idea to replace door lock (just click the up coming site) it. Replacing knobs is an easy DIY project and shouldn't take more than 30 minutes to complete. Use pliers or a screwdriver to remove any knobs or handles. Be cautious not to scratch the other components of the door.

Before you begin, you'll want to spray WD-40 or another dry lubricant onto the mechanism of the door knob. This will allow the new lock to slide smoothly when you turn it. It is essential to choose the best knob and handle that is compatible with your current doors to ensure that the lock is operating properly. If there's no match then you'll have to purchase a new doorknob and latch plate.

Before you begin replacing the knob, take a look at the knob that was previously used to see what screws are keeping it in place. If there aren't any screws, you can make use of a screwdriver and wedge it between the cover plate and the plate with hidden screws and then remove it.

After you have removed the knob examine it for signs of rust and damage. You'll have to scrub it off if there are any scratches or dents however you don't need to do anything major if the knob is in good condition.

Now it's time to install the new one. First, examine the new knobs to make sure that you're selecting the correct one for your door. You'll need to choose one with an extended rod that will interlock with the rod mechanism of the second knob. After you've placed the new knob in the door's hole and then carefully place it in the latch.

Test the spring by pressing down on it repeatedly. The latch should pop up every time. Next, install the other new knob and lock it with the rod mechanism on the previous knob. Then, thread the other long screws from the interior knob through the hole in the cylinder of the doorknob on the outside and secure it.

Latch

A latch is a steel piece that extends into the doorjamb to keep it closed. It is operated by a knob or handle on the inside of the door or a thumb turn on the exterior side of the door. A latch can be secured by deadbolts to prevent thieves from breaking through the glass of the upvc door replacement lock. It also offers protection from the accidental or deliberate closing of the door by pets or children. You can install an entry point with either a single-cylinder deadbolt, or a double-cylinder deadbolt based on your preferred level of security.

Installing a latch involves the same steps as installing a deadbolt, however, there are a few variations. To make sure that the new lock will work, first take a measurement of the setback on the doorjamb with an instrument such as a tape measure. The setback is the distance from the edge of the doorjamb, to the center of the hole to accommodate the latch faceplate. A standard setback is 2 3/8 to 2 3/4 inches. If your setback is larger than that, you might need to purchase an extra-long latch from a hardware or locksmith store.

The next step is to drill an edge bore hole through the doorjamb to accommodate the latch plate. Use a chisel and cut the mortise of the latch. Make sure that the depth is enough to allow the faceplate to be in line with the doorjamb. Tape the strike plate in place to ensure that it's placed correctly.

If the strike is set too high, the door can be pushed in or pressure applied to it using a crowbar or tire iron. This could also cause cracks in the doorjamb. This can be repaired by drilling a new hole in the doorjamb and then removing the core from the old one.

The final step is to mount the new strike plate, which can be accomplished by screwing it over the existing screw holes. Then apply wood putty to cover the old screw holes and the bolt hole that won't be used. After the putty is dry, sand it to an even finish.

Strike

An electric strike is the metal piece where the deadbolt and latch are engaged when the door is shut. It is a crucial component of a lock's overall security, since it helps keep the door shut and also provides additional resistance to force or kicking applied to the door. If a door is equipped with an electronic strike, it can be opened by using an entry key and a control unit that controls its electrical impulses.

Traditionally the installation of an electric strike involved cutting a small portion of the doorjamb to release the latchbolt of a cylindrical lock from the pocket within the strike. This is an issue in terms of the appearance of openings and also exposes the latchbolt and keeper mechanism to unauthorized users.

Recently, a variety of electric strike manufacturers have come up with a "No Cut" type of strike that does not require a cutout to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike has an internal ramp that lifts the latchbolt and keeper whenever it receives an indication from the reader. The retraction of the keeper and latchbolt pushes them up higher on the ramp, locking the door. When the door is shut, the deadbolt stays retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy task, especially when you are replacing the strike on a previous door. If you're planning to upgrade an access control system to an electric strike, it is important to ensure that your new system is compatible. Also, you must make sure that the strike is connected to your access-control system and is configured to function in a safe manner.

One way to safeguard against access by unauthorized persons is to upgrade the strike on your doors to a heavy-duty strike plate. These plates use up to six screws of three inches instead of the usual two screws of three-fourths of an inch. The longer screws make it more difficult for someone to break the frame and then reach inside to turn the thumb turn part of a single deadbolt cylinder.