• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door replace Door Lock Locks

Door locks are your primary protection against unauthorised access to your home. Signs of wear and tear and even instances such as moving into a new residence or break-ins, can necessitate the necessity of replacing your lock.

To begin, you must determine your cylinder size by measuring the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will help you select the appropriate lock.

Deadbolt

Installing a deadbolt is excellent way to protect your door against intruders. When the bolt is extended into the strike plate of the doorframe, it makes it much more difficult for an intruder to get through the door. A single-cylinder deadbolt is activated using a key on the exterior and a thumb-turn piece located on the interior. A deadbolt will only work when it's properly installed however.

First, you'll need to determine if the door has a hole to install deadbolts, or if it requires drilling. Mark the position of the hole for the deadbolt on the surface of the door using the template included with the lock installation set. Use a tape measure to determine the height of the deadbolt. Mark this height on the door edge and use a speedsquare to draw a straight line across the mark you made to mark the bolt hole.

Then by using a power drill, bore through the hole until it is on the opposite side of the door. This could take a while. Then, sand down the hole and the edges of the door until it is smooth. At this stage, it's a great idea also to stain or paint your door.

Remove any screws that are visible from the deadbolt. This will reveal the front and rear assembly of the deadbolt and its bolt inside. Then, remove the bolt and replace door Lock it with a new one that is compatible with your door hardware. It is necessary to remove the bolt from the setplate. After this, you'll need to chisel the area on the door frame for the strike plate.

If your strike plate is not in alignment it could be because the previous installer failed to mortise it properly or that an installation of a weatherstripping altered the strike's position. You'll need to re-mortise your strike plate and possibly even the deadbolt to correct this problem. Once this is completed check the deadbolt by closing it and replacement locking mechanism for upvc doors it. Make sure that the bolt extends into the strike plate and then test the key to ensure it opens and closes easily.

Knob

It could make your home or business less secure If the knob on your door is damaged. It can make opening or closing the door more difficult, so it's a good idea for you to replace it. Replacing knobs is an easy DIY project and shouldn't take less than 30 minutes to complete. Use a screwdriver or pliers to remove any knobs or handles. Be cautious not to scratch the other components of the door.

Before starting you'll need to spray WD-40 or a different dry lubricant onto the mechanism of the door knob. This will allow the lock to move smoothly as you turn it. To ensure proper operation, it's important to choose the right knob and handle to are compatible with your doors. If you don't already have a doorknob that matches then you'll have to purchase a new one.

Before you begin the replacement upvc door lock process, take a look at the knob that was previously used to see what screws are that are holding it in place. If there aren't any screws you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and then remove it.

Once you've removed the knob, check it for signs of rust or damage. You'll have to scrub it up if there are any scratches or marks however you don't need to do anything If the knob is in good shape.

Now it's time to install the new one. It is important to first look over the two knobs to make sure that you've chosen the correct one for your door. You'll need to choose one that has an extending rod designed to interlock with the rod mechanism of the second knob. After you've inserted the new knob into the hole and then put it in the latch.

Test the spring by pressing down on it repeatedly. The latch should spring back up every time. Next, install the other new knob and lock it with the rod mechanism on the first knob. Thread the long screws from the interior doorknob through the holes for the cylinder on the exterior knob, and secure it in the knob's position.

Latch

A latch is a steel piece that extends into the door jamb to keep it shut. The latch is operated either by a handle or knob on the interior of the door, or by a thumb-turn on the outside. Deadbolts can be used to secure a latch and stop intrusions from breaking through the glass of the door. It also protects against the accidental or deliberate closing of the door by children or pets. You can choose to install the latch using either a single-cylinder deadbolt or double-cylinder deadbolt depending on the level you prefer for security.

Installing a latch requires the same steps similar to installing a deadbolt however there are some distinctions. To ensure that the new lock is compatible first, you must measure the setback on the doorjamb with the tape measure. The setback is measured from the edge of doorjamb up to the middle of the hole for the latch plate. A typical setback is 2 3/8 to 2 3/4 inches. If your setback is larger than that, you might need to purchase a latch that is longer from a hardware or locksmith store.

Then, you'll need to make a hole for a latch plate in the edge of the doorjamb. Utilize a chisel to cut the mortise of the latch. Make sure that the depth is sufficient for the faceplate to be in line with the doorjamb. Place the strikeplate on the floor to ensure it is positioned properly.

If the strike is too high, you could push the door back or apply pressure with the tire iron or crowbar. This could cause the doorjamb to break. To correct this, the strike can be lowered by drilling a new hole into the doorjamb and chiseling out the core of the old hole.

The final step is to put in the new strike plate, which is done by screwing it over the screw holes that are already in place. Then, use wood putty to cover the old screw holes and the bolt hole that won't be used. Once the putty has dried you can sand it until it has an even finish.

Strike

An electric strike is the metallic piece that holds the deadbolt and latch engage when the door is shut. It is a vital component of a lock's overall security, because it helps keep the door shut and provides extra resistance to force or kicking applied to the door. If a door is equipped with an electronic strike, it can be opened only with a key and the control unit that controls its electrical impulses.

In the past, installing an electronic strike was as simple as cutting a piece of a doorjamb in order to let the latchbolt of a cylindrical lock from the pocket that is inside the strike. This change can be an inconvenience in terms of the aesthetics of an opening as well as exposing the keeper mechanism and latchbolt cost to replace upvc door lock mechanism near me unintentional users.

Recently, a variety of electric strike manufacturers have developed a "No Cut" kind of strike that does not require a cutout in order to operate. The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that raises the latchbolt and keeper when it receives a signal from a reader. The keeper and latchbolt are pushed on the ramp thanks to the retract. When the door is shut the deadbolt remains extended and the latchbolt is retracted into the keeper.

Installing an electric strike is an easy task, especially when you are replacing door locks the strike on a previous door. If you're upgrading an access control system to an electric strike, you need to ensure that the new system is compatible. Also, you must make sure that the strike is wired to your access control system and that it is configured for fail-safe operation.

Upgrade your strike plates with heavy duty strike plates to stop the entry of unauthorized persons. These plates use four to six screws of three inches instead of the two three-fourth inch screws that are typically used in regular strikes. These longer screws make it difficult for people to break the frame and reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.