• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are your primary line of defense against unauthorized entry into your home. Locks may require replacement due to signs of wear and tear or other circumstances such as moving into a new house or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you purchase the right-sized lock.

Deadbolt

If you want to make sure your door is secure against criminals, it's a great idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe, it makes it more difficult for an intruder to get through the door. A single-cylinder deadbolt is activated by a key located on the outside and a thumb-turn device situated inside. Deadbolts are only effective when it's properly installed, though.

First, you will need to determine if the door has a hole to install deadbolts, or if it needs to be bored out. Mark the position of the hole for the deadbolt on top of the door using the template that came with your lock installation set. Then, you can use your tape measure to determine the height the deadbolt needs to be. Then, mark the height on the side of the door and use a speed square to draw an even line across the mark you made for the bolt hole.

Then, use a power drill to bore out this spot until the hole extends to the opposite side of the door. This could take a while. Sand the hole and edge of the door to make it smooth. At this point, it's a good idea to paint or stain your door.

Once the door is ready remove any screws visible on the existing deadbolt. This will reveal the front and rear assembly of the deadbolt and its internal bolt. Then, remove the bolt and replace door lock (able2know.org) it with an alternative bolt that matches the door hardware. You will need to unscrew the bolt from the setplate. After that, you'll have to chisel the door frame to accommodate the strike plate.

If your strike plate is misaligned it's likely that the previous installer didn't properly mortise it or a weatherstripping popped up and changed the strike's position. To correct this issue it is necessary to remortise the strike plate as well as the deadbolt. Once you have completed this check the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it after the bolt has been extended into the strike plate.

Knob

If a door knob wears out, it can make your business or home less secure. It could also make opening and closing the door more difficult, so it's recommended to replace it. It shouldn't take longer than 30 minutes. You can use a screwdriver or pliers to take off the knob or handle that was previously used Be careful not to harm any other parts on the door.

Spray WD-40, or another dry lubricant, onto the mechanism of your door knob before you begin. This will allow the new lock move smoothly when you turn it. To ensure that it operates properly it is essential to select the right knob and handle to match your existing doors. If you don't already have a matching doorknob and handle, you'll need to purchase a new one.

Before you begin replacing the knob, replace door lock examine the old knob to determine what screws are keeping it in place. If there aren't screws then you can use the screwdriver to secure the cover plate into the screws plate that is hidden.

Once you've removed the knob, check it for indications of damage or rust. You'll need to clean it off if there are any scratches or dents however, you shouldn't need to do anything major when the knob is in good condition.

Install the new knob. Before you do that, look over the two new knobs to ensure you're choosing the right one for your upvc door locks replacement. You'll need to select one with an extended rod that locks with the rod mechanism of the other knob. After you've placed the new knob in the hole and then put it in the latch.

Thread the latch plate screws downwards and then test the spring by pushing down on it repeatedly. The latch should spring back up each time. Then, you can install the new knob and lock it with the rod mechanism on the first knob. Thread in the other long screws from the knob's interior through the hole in the cylinder of the exterior doorknob and lock it in place.

Latch

A latch is a steel piece that extends out into the doorjamb in order to hold it closed. The latch is operated either by a handle or knob on the interior of the door, or a thumb-turn on the exterior. Deadbolts can be used to secure a latch and stop intrusions from breaking through the glass of the door. It also offers protection from accidental or intentional closing of the door by pets or children. The latch can be fitted using one cylinder deadbolt or double glazed door lock replacement cylinder deadbolts according to the security level you prefer.

Installing a deadbolt can be the same as installing a latch, however, there are some distinctions. To ensure that the new lock will fit, first measure the setback on the doorjamb using an instrument such as a tape measure. The setback is measured from the edge of doorjamb up to the middle of the hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If you have a greater setback, you may need to purchase a more substantial latch from a hardware shop or locksmith.

Then, make a hole for the latch plate at the edge of the doorjamb. Utilize a chisel to cut the mortise of the latch. Make sure the depth is sufficient for the faceplate to be in line with the doorjamb. Put the strike plate into place to make sure it's in the right position.

If the strike is too high, you could knock the door down or apply pressure with the tire iron or crowbar. This can cause the doorjamb to break. To correct this issue, the strike can be lowered by drilling a new hole in the doorjamb and cutting out the core of the old hole.

The last step is to put in the new strike plate which is done by screwing it in place over the screw holes that are already in place. Use wood putty then to fill in any existing bolt holes or screw holes which aren't going to be used. After the putty has dried you can sand it until it has an even finish.

Strike

An electric strike is the metal part where the deadbolt and latch engage when the door is shut. It is a crucial component of a lock's overall security, as it keeps the door shut and provides extra resistance to force or kicks applied to the door. If a door is equipped with an electronic strike, it will be opened only with keys and the control unit that regulates its electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a portion of a doorjamb in order to let the latchbolt of a cylindrical lock from the pocket within the strike. This modification can be an issue when it comes to the aesthetics of an opening as well as exposing the latchbolt and keeper mechanism to unintentional users.

Recently, a variety of electric strike manufacturers have come up with a "No Cut" kind of strike that does not require a cutout for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without damaging the doorjamb's faceplate.

The strike is equipped with an internal ramp that raises the latchbolt and keeper when it receives an electrical impulse from a controller or reader. The retracting of the keeper and latchbolt raises them on the ramp, locking the door. When the door is closed, the deadbolt remains in place and the latchbolt retracts into the keeper.

Installing an electric strike is a simple process, especially when you are replacing a upvc door lock the strike on a previous door. If you are upgrading an existing access control system to an electric strike, it is important to ensure that the new system is compatible. It is also necessary to make sure that the strike is wired to your access control system and that it is set up for fail-safe operation.

One way to safeguard against intrusions by thieves is to upgrade the strike on your doors to a robust strike plate. The plates are made of up to six screws of three inches instead of two screws of three-fourths of an inch. These longer screws make breaking the frame to reach the thumb turn piece on a single cylinder deadbolt more difficult.