• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Go About boarding up companies Up a Door

boarding up houses up a door [find more info] is one method to shield vacant investment properties from the elements. While it may not prevent all damage, it can avoid some of the problems that can arise from severe storms.

The idea of emergency boarding up 24/7 up doors and windows can deter trespassers or vandals from entering your property. Placing plywood boards over doors and windows could be time-consuming and costly.

Measure the Door

You'll first need a tape measure. You may also want to have a ladder or chair handy in case you have to get a better look at the top of the frame. If you have to use these tools, be sure to wear gloves and safety glasses.

Once you have the measuring tool, begin by taking the door's width measurement. This can be accomplished by running the tape horizontally across the door. Be sure to remove all extra parts of the door, Boarding Up a Door such as a sweep, before measuring. Next, take the height measurement by measuring up from the floor to the current sill plate or lintel. It is essential to measure in multiple locations, boarding up a door particularly when measuring older doors as they might not be a perfect rectangular shape. If the measurements differ, use the largest number.

You'll need to determine the size of the frame once you've measured the height and width. Ideally, it should be 2 inches wider than the door and 1 2'' higher. This will give enough space to shim both the frame and frame to fit.

When you're ready to measure the door frame's width and height measurements, it's best to take out any trim or casing from around the door jambs so you can see the studs behind them. This will allow you to measure the exact gap between the studs of the frame and the edge.

Once you've removed the trim, you can determine the size of the frame of your door by running the tape across the entire frame in three places and using the smallest measurement as the width of your door. Also, you should determine the height of the frame from top to bottom on both sides. Use the shortest measurement to determine your door's width.

If you are having trouble with the measurements, you should consult a professional to come to your home and take the measuring. They'll inform you of the size and style of door you require and how to prepare your frame to accommodate a replacement door.

Cut the Plywood

A door frame is usually composed of studs or boards that create an open space around the door. Two hinges are attached to the studs and hold a typical door in place. This means that if you need to finish the door, it is essential to take the door from its hinges for a night. Placing plywood in the door opening is a great way to board the door and keep insects from getting into your home. It's easy to do this without nailing or screw the plywood onto the door's frame.

Plywood is a breeze to work with, cheap and looks great once it's completed. This makes it the ideal material for an interim solution to a problem that requires removing the door that is in use and renovating or installing a brand new one. It can also be used to secure the opening of a room that is being renovated, like the construction site or basement.

Start by taking measurements of the width of the door opening and its height. Mark the measurements with a utility blade and a metal straight edge like a drywall or a metal square. Then, draw the chalkline along each line to mark the area to cut. Finally you can use circular saws to cut out the plywood into a size.

When cutting the plywood, it is essential to protect your eyes and ears. If possible wear safety goggles and earplugs when working. In addition, it's important to use a blade with a large number of teeth that can cut quickly and without tear-out. Utilize a small piece of wood to guide the blade. Hold it about a hair's width away from the line you are cutting.

A good way to keep the plywood in place without screwing it to the studs is to attach braces that are short at each end. Place one of the braces on the inside of the door and the one on the outside. Position a pair 1-1/2-inch deck screw in each hole and tighten using an open-end ratchet.

Fix the Plywood

Once you have a sheet of plywood cut to the proper dimensions and with the holes for the door frame's stiles and rails predrilled then it's time to fasten the panel to the frame. This is a simple project that doesn't require a lot of advanced carpentry skills, as long as you have the right tools and follow the right procedure.

Set up a table near the doorway with two sawhorses at each end and framing lumber 2x4s. Utilize the marks you made during the measurement process to guide you while cutting the plywood. Utilize a utility blade and a metal straight edge to cut the lines. This will serve as a guide to the saw blade and prevent splintering of the plywood when cutting it.

Wear eye protection and use a circular or table saw equipped with a fine-toothed blade cut along the line of scoring. Then sand the edges of the plywood panel using 120-grit sandpaper. This will smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding the plywood panels apply a wood sealer and allow it to dry in accordance with the manufacturer's guidelines.

Install the hinges on the frame of the door. If you are using a T hinge, drill holes through the exterior of the door for the straps of the hinges. Then, you can screw the hinge on the outside to the frame using a screwdriver. Repeat the process for every hinge on the inside of your door. Be cautious not to tighten them too much or the panel could shift.

If you are using a single outside T-hinged door, you can make it easier to close and lock with a chain lock by putting a piece wire through the loops on the outside hinges. Bend a short piece of tie wire in half and place it through the two holes on the outside of the door. You can then twist the wires to pull them tightly and fix the door.

Install the Plywood

Place the plywood in the door's opening according to the measurements you took. Change the header of the frame (top) and the sill. Use a level and ensure that there's no slop between the sill and the header. If it's not perfect, place another shim where required and repeat the process until the sill and header are level.

Once the plywood is in the frame, fix it with the stainless steel hinge bolts and wing nuts. Use a screwgun with an attachment for hex heads to avoid stripping off the screws' heads.

While you're at it if your house was built with studs that extend the height of your doorway, drill hanger bolts through the plywood and into each framing stud. This is a simpler job than making the hole using the drywall saw.

After putting the plywood in place take measurements of the width and height of the door opening. If necessary, trim your plywood bottom to fit the height of your door frame. Cut two pieces of framing lumber 1 by 6 as braces for the upper and lower edges. Wear eye protection and cut along the lines marked on the plywood using a circular saw fitted with a fine-tooth blade. Splinters can be removed from the cuts using a sanding tool.

After you've put in the braces after you have positioned them, use two pairs of finishing nails that measure 2 inches to join each brace to the plywood. When you're finished, counter sink the heads of all nails. Cover the braces using a high-quality wood sealing product, like the wipe-on polyurethane from Minwax.

If the door is too big for your doorway, you can put in an ornamental molding to fill in the space between the jamb and the door or alter the size of the opening. However, in most instances, it's cheaper and more convenient to find a new door. It also removes any problems you might have encountered with your door's original model in the event that it was damaged or not suitable for the opening.