• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace upvc door lock mechanism Door Locks

Door locks are your primary line of defense against unauthorized entry into your home. Locks may need to be replaced due to wear and tear or other circumstances like moving into a new residence or a break-in.

To begin, you must determine the size of your cylinder using the distance between the adjustment screw and the center of the knob lock cylinder. This measurement will assist you select the appropriate lock.

Deadbolt

If you want to ensure your door is safe from burglars, it's a good idea to install a deadbolt. The bolt extends into the strike plate on the doorframe when locked, making it more difficult for a burglar to gain entry through the door. A single-cylinder deadbolt can be activated by a key located on the exterior and the thumb-turn mechanism situated inside. A deadbolt will only work if it's installed correctly however.

You will first need to find out if the door has an existing hole for a deadbolt, or if you need to bore it out. Mark the position of the hole for the deadbolt on the exterior of the door using the template that came with your lock installation set. Utilize your tape measure to determine the height of the deadbolt. Then, mark this height on the edge of the door. Use a speed square to draw straight lines across the mark you made for the bolt hole.

Then, use a drill to drill this hole until it extends to the opposite side of the composite door replacement lock. It may take a while. Sand the hole and edge of the door to smooth it. At this stage, Front Door Lock Replacement Cost it's a great idea also to stain or paint your door.

When the door is open take off any screws visible on the deadbolt. This will reveal both the Front Door Lock Replacement Cost and rear assembly of the deadbolt as well as its bolt inside. Then, remove the bolt and replace it with a brand new one that matches the door hardware. It is necessary to remove the bolt from the setplate. Then, you'll need to chisel the surface of the door frame to accommodate the strike plate.

If your strike plate isn't aligned properly It's likely that the previous installer didn't correctly mortise it or a weatherstripping popped up and changed the strike's position. To fix this problem you'll need to remortise both the strike plate and the deadbolt. Once this is completed check the deadbolt by closing and locking it. Test the deadbolt by closing it and locking it after the bolt has been extended into the strike plate.

Knob

If a door knob wears out it could make your business or home less secure. It may make it more difficult to open or close the door, so it's a good idea to replace it. replacing a patio door lock a knob is a relatively easy DIY task that should not take less than 30 minutes to complete. You can use a screwdriver and pliers to remove the old knob or handle However, be careful not to scratch any of the other components on the door.

Spray WD-40, or a different dry lubricant, on the mechanism of your door knob before you begin. This will allow the new lock slide smoothly as you turn it. It is essential to choose a quality knob and handle that matches the doors you currently have to ensure that the lock is operating properly. If you don't have a matching doorknob, you will need to buy a replacement.

To begin the replacement process, look at the knob or handle to see what screws are holding it in place. If there aren't any screws you can use a screwdriver to wedge between the cover plate and the screws plate hidden and remove it.

After you've removed your knob, check it for signs of rust or damage. You'll need to clean it off if there are any marks or dents however, you shouldn't need to do anything major when the knob is in good shape.

Now it's time to install the new knob. Before you do that, look over the two new knobs to make sure that you're choosing the right one for your door. You should select one with an extending rod that is designed to lock with the rod mechanism of the second knob. After you've inserted the new knob in the hole then slide it into the latch.

Test the spring by pressing it repeatedly. The latch should pop up each time. Then, you can install the new knob and lock it with the rod mechanism on the first knob. Thread the long screws from the interior doorknob into the holes for the cylinder on the exterior knob and lock it into the knob's position.

Latch

A latch is a metallic piece that extends into the door jamb in order to hold it closed. The latch can be operated by a handle or knob on the interior of the door, or by a thumb-turn on the outside. A deadbolt can be used to secure a latch and prevent intrusions from breaking through the glass of the door. It can also guard against intentional or accidental closing by animals or children. The latch can be fitted with one cylinder deadbolt or double cylinder deadbolts depending on the security level you prefer.

Installing a latch follows the same steps like installing a deadbolt however there are some variations. First, measure the setback of the doorjamb by using an instrument to make sure that the new lock will fit. The setback is measured from the edge of doorjamb up to the middle of the hole for the latch plate. A standard setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you may have to purchase a longer latch from a hardware shop or locksmith.

The next step is to drill an edge bore hole in the doorjamb for the latch plate. Use a chisel for chiseling out the latch mortise making sure it's large enough to allow the faceplate of the new latch to be flush with the doorjamb. Place the strike plate in place to ensure that it is positioned correctly.

If the strike is too high, you can kick the door in or apply pressure with an iron tire or crowbar. This could also cause cracks in the doorjamb. This can be corrected by drilling a new hole through the doorjamb, then cutting the core from the hole that was previously made.

Installing the new strike plate is the last step. This can be done by screwing the new plate into the screw holes that are already in place. Then you can use wood putty to cover the screw holes that were previously used and the bolt hole that is not used. When the putty is dry, sand it smooth for an elegant finish.

Strike

The metal piece that engages the latch and deadbolt when the door is shut is an electric strike. It is a vital part of the lock's security because it prevents the door from opening and provides an additional level of resistance to force or kick. If a door is equipped with an electronic strike, it can be opened only by a key and the control unit that regulates the electrical impulses.

In the past, putting in an electronic strike required cutting a piece of a doorjamb to remove the latchbolt on a cylindrical lock from the pocket inside the strike. This modification is not just undesirable and unattractive, but also exposes the mechanism for the latchbolt and keeper to uninitiated users.

Recently, several electric strike manufacturers have created a brand new electric strike, dubbed the "No Cut" strike that doesn't need an opening in the doorjamb for operation. They use a specific design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike has an internal ramp that lifts the latchbolt and keeper when it receives an indication from an individual reader. The retracting of the keeper as well as latchbolt raises them on the ramp, which locks the door. When the door is closed the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy process, particularly in the case of replacing an existing strike door. If you're planning to upgrade an access control system to an electric strike, it is important to ensure that the new system is compatible. You will also have to ensure that the strike is properly connected to your access-control system and is configured to operate in a fail-safe way.

Upgrade your strike plates to heavy duty strike plates to prevent the entry of unauthorized persons. The plates utilize four to six screws of three inches instead of the two, three-fourth inch screws typically used in regular strikes. The longer screws make it difficult for anyone to break the frame and reach inside to turn the thumb turn part of a single cylinder deadbolt.