• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Repair French Doors

French doors are a stylish addition to any home that connects outdoor and indoor spaces. They can develop problems in time, and require immediate attention to ensure security and function.

Common problems include problems with alignment, sagging, and warping of the door frame and sash. Many of these issues can be easily resolved with just a bit of time and effort.

Misaligned Locks

Some doors can become stuck or misaligned due to humidity, wood swelling or house settle. This can cause the bolt for the lock to become loose, making it harder to open or close the door. This could put additional strain on the locks, which may eventually lead to broken locks or mangled components. Fortunately, this is an issue that is common and can often be solved with simple DIY techniques.

In certain situations there are times when a tiny amount of lubricant may be enough to make the door easier to open and close. You can use a graphite lubricant but make sure that it is safe for the door. Make sure you clean the area with a moist cloth to clean any debris from around the door before applying the oil.

A door that hangs off-center is easily fixed by loosening and adjusting the hinges until they are aligned with the frame. Be careful not to tighten the screws too much because this could damage the hinges or the door.

If your exterior French doors aren't closing properly, this could be an indication that there is an obstruction in the lock mechanism. This is usually caused by short screws from the factory that have become loose over time. Replace the screws with larger ones to pull more wood from the door frames.

You can also try adjusting the lock itself, however this is more difficult and complicated. Begin by loosening either the lock knob or handle using flathead screw. You can then remove the lock assembly from its cubbyhole by removing it and taking it out. Examine for obstructions, then reassemble it, and tighten all the screw connections.

If the latch doesn't hit the strike plate, you might need to move the strike plate or expand it. If the strike plate is smaller or higher than the hole of the latch, Repair French Doors it could hinder the lock from closing and require a locksmith. If the hole is tiny it is possible to use a metal file to make it larger.

Sagging

If your doors are sliding or have gaps between them, it will affect the insulating properties of your house and decrease its energy efficiency. These gaps can also create drafts that block your view. Fortunately there are simple solutions to help solve these problems.

Begin by tightening the hinges and aligning them correctly. This should take 10 minutes or less and not require any tools. If this doesn't fix the problem then you'll need to replace the hinges. They're likely to be to be at the end of their lifespan.

Over time the weight of your French door may cause them to become slack. To prevent this from happening make sure that the hinges are tightened on your door and ensure they are secure. It is also recommended to regularly lubricate your hinges with a spray of lubricant to prolong their life.

Replace hinges that are damaged or worn out to prevent a door from sliding. A new doorknob or freshly painted doors could also impact the alignment of your French door.

Other causes of sagging include foundation settlement or wear and tear on the hinges, or inadequate modifications to your doors. You can fix a sagging door by tightening or adjusting the hinges.

Also, it is important to check the weather stripping on your doors and to ensure that they're working properly. If they are not, then removing them and replacing french door glass them could fix the issue.

Finally, you should regularly examine the wood on the door frame for signs of warping or rotting. These issues can lead to drafts, which can decrease the effectiveness of your door. They can also lead to water leakage and other damage around your home.

Popular Mechanics advises that if your doors are sliding after you've tried the first two options, you may have to sand your door jambs with a handplane. To do this, take your doors from their hinges. Place them flat on a solid surface like a sawhorse. Note the areas that require smoothing, and then use a plane to smooth these areas.

Leaks

French doors with large glass areas are more prone to leaks, particularly if you live in an area that experiences frequent rain. If left untreated, these leaks could cause the frame of the door to decay and damage the structure around it to deteriorate. It is fairly simple to repair these leaks, and it should only take you a few minutes.

Leaks can be caused by a number of factors, including:

A broken seal

This issue can be solved by replacing the rubber seal on either side of the threshold with a a new one. This will ensure a tight fit, and will also stop rainwater from getting into your home.

Water leaking through the sill

The problem could result from a variety of issues, including a absence of a sill pan or by the use of a metal sill that isn't watertight. If you notice that water is accumulating around your French doors, it is important to contact the builder and ask them to install sill pans or replace the sill made of steel by a wooden one that will be able to resist moisture.

Obstructions

A damaged seal could cause fog to build up between the double panes on French doors. This can obstruct the view and reduce their energy efficiency. This can be corrected by replacing the existing seal with a fresh one that can keep out moisture and air.

Loose Handles

A handle that isn't tight could be dangerous because it could fall when you're opening or closing your French door. This issue can be resolved by tightening the screws, or replacing the handle if it's damaged or worn.

A track stop that's not correctly set can prevent doors from sliding in the right way, leading to scratches and jams on frames. Adding some silicone caulk to the tracks or track stops can aid in solving this issue. You should also regularly check the exterior surfaces of frames and doors for cracks or wear to ensure that they are in good working order.

Warping

A french door window frame replacement door is a beautiful view and lets in lots of natural light, but if you're not careful your doors may begin to warp due to exposure to heat or humidity. If this happens, consider calling a handyman that specializes in repairing replacement french door doors. They will be able to advise on the best way to repair your doors and make sure that they are safe to open and close.

If your doors are severely warped, you might need to replace them completely. If they are just slightly warped, you may be in a position to straighten them by placing damp towels over the affected area. The towels should remain in place for a couple of days or until the doors are flattened completely.

This technique is typically used on replacement upvc french doors doors, but it could also be applied to wood ones if the wood is well-seasoned. The process is laborious and time-consuming, particularly if your doors are warped.

The doors can warp when they are stored improperly. They should be kept away from construction projects that create a lot of humidity like decorating or plastering work. They should be kept flat on a firm surface.

Another cause of warping is the strike plate being loose. To fix the issue, you will need to take the doors off and put them on a pair sawhorses. You can then employ a hand-planer to remove any excess wood from the top and bottom of each door. It is essential to work in small steps so you don't end up cutting too much off the doors, which could cause them to become too thin and Repair French Doors brittle.

Once the doors are fixed, you can put the strike plate back into place. If the lock doesn't work, the barrel catch may be catching against the side of the frame. This can be fixed by spraying silicone onto the latch. If this doesn't work, you may need to replace the latch.