• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

boarding up companies Up windows (postheaven.net) and Doors Before a Storm Hits

The act of boarding up your windows and doorways before an event can give you measurable protection against damage. To do this, you'll must have a few things in the go.

Find the height and width of the window, including the frame (not the trim or the masonry around the window). Note these measurements down to ensure you don't forget them.

Preparation

It is always best to put up a board on doors and windows before an event like a storm or natural disaster strikes. This will minimize damage to property and decrease the chance of dying. boarding up a doorway up windows requires a lot of preparation, such as buying and measuring plywood boards as well as identifying the exact size of each window that needs to be covered. Moreover, it takes time to cut the boards and install them properly. Fortunately, the process can be made simpler by preparing immediately you learn of a possible storm coming in your area. You will avoid having to rush in the last minute, and make it simpler for you and your staff.

Begin by listening to forecasters of the weather and following the guidelines provided by your local government. The earlier you begin the process, you'll have more time to collect the materials and store them without feeling rushed by an approaching storm. It is possible that you will require a large amount of plywood to cover your windows dependent on the severity and speed of the storm. To ensure you get the correct size, make use of a tape measure to determine the height and width of each window opening. Be sure to include the trim or framing around each window, as well as any ledges with extended edges if they are necessary.

Then, calculate the dimensions of the sheets of plywood you require by dividing the total window width and height by 2. For example, if width of your window is 16 inches, the thickness of each sheet should be 8 inches. If you have an exterior made of wood, you should drill pilot holes in the plywood sheet that align with the window frame underneath to prevent splitting when screwing into the screws.

If you have a larger window opening than one sheet of plywood can handle cut two sheets of plywood that are each half as big as the window you want to use. Then, place them side-by-side on the wall. Then, cut a piece of 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edges of the plywood sheets and then place it over the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them.

Materials

To ensure security and safety ensure safety and security, use only materials that are sturdy and won't break or shatter in strong winds. Plywood is the most common material to board up windows. It is easy to use, affordable and readily available. Pick plywood that is exterior grade (CDX), as it will be stronger and contain fewer warps and knots. A stronger option is hurricane or storm shutters, which are erected over windows already in use to offer more protection against glass shattering and the weather that can cause a lot of damage.

Once you have identified the location of the window openings, you can take measurements of the height and width to determine the amount of plywood you will require. Then make use of the power drill to drill pilot holes in the plywood sheets at two-inch intervals around each window. Mark the studs on the wall prior to attaching the plywood to ensure that the boards are secured. If your home is constructed with wood siding, look for nailheads that could indicate stud locations. Otherwise, Boarding up windows you can probe service for boarding up windows stud positions with your drill. The screws should be driven into the framing, not into the trim or sheathing. A plywood panel bonded only to these materials can be a danger to safety in severe winds.

If your window is too big for one sheet of plywood, cut two pieces of plywood that are each half the size and join them using 2 by 4 inches of lumber. Label each plywood panel to let you know what window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing as well as the studs that will be used to join the plywood panels to the wall. To secure the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to get through both the sheathing and the studs.

In addition to protecting your windows, you should install an "No Trespassing" notice on the property, and consider installing polycarbonate security glazing like DefenseLite over your windows. These transparent shields bond over existing glazing to protect your windows and doors and are virtually unbreakable, deterring criminals from gaining entry.

Installation

If you live in or are planning to move to a region susceptible to hurricanes and are concerned about the possibility of a storm, it's best to board up your doors and windows. It's a task that can be done quickly and efficiently however only if you take the time to measure and cut, then label your plywood panels prior to when the storm hits.

You'll need additional tools, including the drill, a saw (or a hammer with nails for those who don't have a power tool) as well as a level, gloves, and safety glasses. It's a good idea coat the plywood with sealant, as well, to make it waterproof.

Start by measuring the window's width and height. Then cut the plywood sheets to fit into the frames. It is recommended to cut the sheets on site, since it gives you more control over the precise dimensions of the plywood.

Use a circular saw or track saw to cut the boards to size, and remember that you'll have to sand them off once they're installed. Once you've put your boards in place, screw three-inch stainless steel hanger bolts into the framing studs around each window. Use washers on each bolt and wings nuts to secure them. Make sure that each screw is inserted at least 2 inches deep into the studs to ensure that the boarding is sturdy enough to withstand the force of high winds.

If you're building using concrete block, you can instead join the plywood to the building using galvanized pan-head screws driven through the edges that overlap of each panel to form cinder blocks or masonry blocks. You'll also need to drill pilot holes in the masonry, and then insert corrosion-resistant screws into the holes. It's a job that could take as long as three hours per window, so it's essential to begin the process immediately after you hear that a hurricane watch has been issued. This will give you enough time to complete your project before the storm hits.

Maintenance

If you're a homeowner or business owner, you should have the required materials to board up windows and doors in advance of a severe storm. This can help you avoid costly repairs and protect your home from further damage caused by wind, rain debris, flying debris and other elements that can affect windows.

The right tools can make the boarding up windows near me up process much easier and quicker to complete. It is essential to precisely measure the windows. This will ensure the OSB or plywood fits well and will not fall off easily. If you're using plywood, be sure to use sheets of exterior grade and think about adding a protective finish.

Note the locations where the screws will need to be put into the board after you have measured the OSB or plywood. Utilize a drill to predrill holes at 12-inch intervals in the plywood. This will allow you to securely fix the boards using hanger bolts in a disaster or emergency boarding up service situation. Once the storm has passed and the local authorities have given you the all-clear, remove the bolts, but save them in case of a need in the future.

Then, you can put the plywood panels on top of the windows. This is a job for two people So, be prepared before you start. If you're using wood, Boarding up windows make sure you sand the edges to ensure they're smooth and won't scratch paint or trim. Then, attach the plywood to the frame with screws that are corrosion-resistant and fit into the pilot holes. If your home has vinyl shingles on it, nail the plywood directly to the shingles and not the wood framing.

Apart from keeping out water and other weather elements, a boarded up window is also an effective method to stop burglaries. Burglars are more likely to target a property with a damaged window or one that's not secured. They're also more likely to attack the store that has been boarded up as opposed to one that's not. If you're a retail business owner, this is something you must take seriously.