• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat 500 car key cover 500 Key Fob Won't Work

A key fob for the fiat keys 500 allows you to easily open doors and start your vehicle. There are many reasons why the fob could stop working. These include a dead coin battery, damage to the receiver module, issues, and interference.

This listing is for a NEW replacement fiat scudo key Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't work is a dead battery. Modern key fobs operate with a limited operating range, and should be within some feet of the vehicle in order to function. If you are far from your vehicle when you press the key fob button the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin cell battery (Part number CR2032) with a fresh one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can find them in your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your fiat key case replacement fiat 500 key fob not working. The parking lights should blink and the key fob should operate the lock and unlock switch.

If your key fob doesn't work even after replacing the battery, it may be water damage which is preventing it from connecting to the module inside your vehicle. Water damage can occur in a number of ways, from the slightest splash to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this fails, you'll require your fob to be reset by an auto locksmith or a dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean, or wash it in a washer. Saltwater can cause the circuit board to short and eventually cease to function. It's not good to soak the fob in water however, don't give it up even if you accidentally drop the fob in water, freeurlredirect.com or fail to take it out of your pocket.

First, remove the battery. Clean the electronic chip with isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Check the fob to determine if it's working. If the key isn't working, it may have to be reset. This is usually done by an auto locksmith or dealer.

If the key is older and was not programmed to your car It will most likely need to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith will need the key cut to match your car's ignition. They'll also need to reprogram the fob to the car's system. This is a cheap and quick process that can be completed the same day.

Receiver Module Issues

Your 500 key fob may not work because it's out of range. The remote typically has an operating range of 30 feet or less and if it's far from your vehicle, it will not respond to your commands. It is possible to remedy this by moving your remote closer to your car until it responds.

If you've replaced the coin battery (commonly called"button" or "button" or "watch") and your fob doesn't function it could be due to an internal circuit board problem. In most cases, reprogramming the fob can resolve the issue. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.

It is possible to replace the metal clips that hold the coin batteries in place. If they loose tension they could stop the battery from sitting properly and can cause your remote to malfunction.

In rare cases, the fob may become disconnected from your vehicle due to software problems or hardware issues. This could cause a significant issue, but you are able to often fix this by visiting an auto locksmith to have them reprogram your fob for you. In certain instances it may be necessary to install the software again in your body control module, too.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This could occur if the keyfob is in close proximity to a radio transmitter, such as a cell phone or radar detector. Other reasons why the key fob could not function may be a lack of connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, this page or if you have tried everything at home to fix it (e.g. battery replacement, reprogramming and using the spare key fob, you may have a faulty receiver module on your 500. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then read by the vehicle.

There's a simple method to reset the 500's on-board system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by taking off the negative cable first then the positive cable. Then reconnect the battery. This will remove any remaining electricity, and allow you to restart the car's computer. This can help get your key fob to work again. If the problem persists it is recommended that you consult a certified technician. They'll be able to determine the exact cause of your problems.