• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are the first security measure against unauthorized entry into your home. The signs of wear and tear, and also instances like moving into a new residence or burglaries, could trigger the necessity of replacing your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to purchase the correct-sized lock.

Deadbolt

Installing a deadbolt is great way to secure your door from burglars. The bolt extends into the strike plate that is on the doorframe when locked, making it more difficult for burglars to break in through the door. A single cylinder deadbolt can be activated with keys on the exterior side and a thumb turn device on the inside. Deadbolts can only function when it is properly installed.

It is first necessary to find out if the door has a hole that is suitable for a deadbolt or if you have to drill it out. Mark the location of the hole for the deadbolt on the surface of the door by using the template supplied with the lock installation set. Use a tape measure to determine the height of the deadbolt. Mark this high point on the door's edge and use speedsquares to draw a straightline across the mark you made to mark the bolt hole.

Then using a power drill, bore out the hole until it is on the opposite side of the door. This could take a while. Sand the hole and the edge of the door to make it smooth. It's also a good idea to paint or stain the door at this point.

Remove any screws that are visible from the deadbolt. This will reveal the rear and front assembly of the deadbolt as well as its internal bolt. Then, unscrew the bolt and replace door lock, new content from cameradb.review, it with a brand new bolt that matches your door hardware. The bolt is usually attached to a set plate that you need to unscrew. After that, you will need to chisel out the area for the strike plate on the door frame.

If your strike plate is not in alignment, Replace Door lock it could be because the previous installer didn't mortise it correctly or a weatherstripping has changed the strike's position. To fix this problem, you will need to remortise both the strike plate and the deadbolt. Close and lock the deadbolt after you have completed this step. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

It can make your home and business less secure if the replacement door locks knob is damaged. It could make opening or closing the door more difficult, so it is recommended to replace the knob. Replacing knobs is an easy DIY task that should not take more than 30 minutes to complete. You can use a screwdriver as well as pliers to get rid of the old knob or handle, but be careful not to scratch any of the other components on the door.

Spray WD-40, or another dry lubricant on the mechanism of your door knob before you begin. This will allow the new lock to slide smoothly when you turn it. It's essential to select the best knob and handle that is compatible with your doors currently in order to ensure proper operation. If you don't have a match you'll need to purchase a new doorknob and latch plate.

Before you begin replacing lock on upvc door the knob, take a look at the knob that was previously used to determine which screws are holding it in place. If there are no screws then you can use the screwdriver to wedge the cover plate in between the screws plate that is hidden.

After you've removed your knob that was previously used, look it over for any indications of damage or rust. If the knob shows any scratches or marks it's time clean it. Otherwise it shouldn't require any major work.

Install the new knob. Before you do that, look over the new knobs to ensure that you're selecting the correct one for your door. You'll need to choose one with an extender rod that will interlock with the rod mechanism of the second knob. Once you've put the new knob into the hole and then put it in the latch.

Thread the latch plate screws down and then test the spring by pressing down repeatedly. The latch should pop up every time. Then, you can install the new knob and connect it with the rod mechanism on the previous knob. Thread the long screws from the doorknob's interior through the cylinder holes on the exterior knob, and fix it in the knob's position.

Latch

A latch is a piece metal that extends into the doorjamb to secure it shut. The latch is operated by a handle or knob located inside the door, or a thumb-turn on the outside. A deadbolt can be used to secure a latch and stop intrusions from breaking through the glass of the door. It also provides protection from the accidental or deliberate closing of the door lock replacement near me by pets or children. You can install the latch using either a single-cylinder deadbolt, or a double-cylinder deadbolt, depending on the level of security.

Installing a latch requires the same steps similar to installing a deadbolt however, there are a few distinctions. To make sure that the new lock will fit first, you must determine the setback of the doorjamb with the tape measure. The setback is measured from the edge of doorjamb all the way to the center of hole for the latch plate. The standard setback is 2 3/8 to 2 3/4 inches. If your setback is greater than that, you might need to purchase a latch that is larger from a locksmith or hardware store.

The next step is to drill an edge bore hole into the doorjamb to accommodate the latch plate. Use a chisel to chisel out the latch mortise, making sure it's deep enough for the faceplate of the new latch to sit flush with the doorjamb. Tape the strikeplate in place to ensure it is positioned properly.

If the strike is placed too high, the door could be pushed into or pressure put on it with a crowbar or tire iron. This can cause cracks to the doorjamb. To remedy this, the strike could be lowered by drilling a new hole into the doorjamb and chiseling out the center of the hole that was previously drilled.

Installing the new strike plate is the last step. This can be done by screwing the new plate over the existing screwholes. Use wood putty afterwards to fill in any existing screw holes or bolt holes that aren't being used. Once the putty has dried, sand it to a smooth finish.

Strike

The metal piece that engages the latch and deadbolt when the door is closed is an electric strike. It is a vital part of the lock's overall security because it prevents the door from opening and gives an additional barrier to force or kicking. If a door is equipped with an electronic strike, it can be opened by using a key and the control unit that regulates the electrical impulses.

Traditionally, installing an electric strike required cutting out a portion of the doorjamb to remotely remove the latchbolt of a circular lock from the pocket within the strike. This is not only ugly, but also exposes the mechanism for the latchbolt and keeper to uninitiated users.

Recently, a number of electric strike manufacturers have created a new type of electric strike called the "No Cut" strike that doesn't require an opening in the doorjamb to function. These strikes utilize a special design to allow the keeper and latchbolt to slide into the strike pocket without marring the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper whenever it receives an electrical impulse from a reader or controller. The retraction of the keeper and latchbolt raises them on the ramp, thereby locking the door. When the door is closed the deadbolt remains in retracted and the latchbolt retracts into the keeper.

Installing an electric strike can be an easy task, especially in the case of replacing a upvc door lock an existing strike door. If you are upgrading an existing access control system to an electric strike, it is important to ensure that your new system is compatible. It is also necessary to ensure that the strike is wired to your access control system and that it is set up for fail-safe operation.

One way to protect against unauthorized access is to upgrade the strike on your doors to a high-quality strike plate. The plates are made of up to six screws of three inches instead of the standard two screws of three-fourths inches. These longer screws make breaking the frame to reach the thumb turn piece on a single deadbolt for a cylinder more difficult.