• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to replace door lock Door Locks

Door locks are your primary line of defense against unauthorized access to your home. The locks may require replacement due to wear and tear, or other situations like moving into a new house or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the appropriate lock.

Deadbolt

If you want to make sure your door is secure against criminals, it's a great idea to install deadbolts. The bolt extends into the strike plate on the doorframe when locked, making it more difficult for a burglar to gain entry through the door. A single cylinder deadbolt is activated using keys on the exterior side and a thumb turn part on the interior. Deadbolts will only work if it is installed correctly.

First, you'll need to determine if the door already has a hole to install deadbolts, or if it requires drilling. Mark the location of the hole to install the deadbolt on top of the door by using the template supplied with the lock installation set. Then, use the tape measure to determine the height the deadbolt needs to be. Mark this height on the door edge. Use the speedsquare to draw a straightline across the mark you made to mark the bolt hole.

Then, replace door lock use a drill to bore this area until the hole is on the other side of the door. It may take a while. Sand the hole and edge of the door to make it smooth. At this stage, it's a great idea also to paint or stain your door.

Remove any visible screws from the deadbolt. This will reveal the rear and front assembly of the deadbolt and its internal bolt. Then, remove the bolt and replace it with a brand new bolt that matches your door hardware. It is necessary to remove the bolt from a setplate. Then, you'll need to chisel the surface of the door frame to accommodate the strike plate.

If your strike plate is out of alignment, it could be because the previous installer did not mortise it properly or that a weatherstripping has changed the strike position. To fix this issue, you will need to remortise the strike plate as well as the deadbolt. Once you have completed this check the deadbolt by closing it and locking it. Test the deadbolt by closing it and locking it after the bolt has been extended into the strike plate.

Knob

It could make your home and business less secure if the door knob is damaged. It can make it more difficult to open or close the door, which is why it's recommended to replace lock in upvc door the knob. It shouldn't take longer than 30 minutes. You can use a screwdriver and pliers to take off the knob or handle Be careful not to harm any other parts on the door.

Before starting you'll need to spray WD-40 or another dry lubricant onto the mechanism of the knob for your door. This will help the new lock to slide effortlessly when you turn it. It's essential to select the best knob and handle that matches your doors currently in order to ensure that the lock is operating properly. If you don't have a match you'll need to purchase a replacement lock for upvc door doorknob and latch plate.

Before you begin the replacement process, look over the knob you replaced to see what screws are keeping it in place. If there aren't screws, you can use the screwdriver to wedge the cover plate between the screws plate hidden behind it.

After removing the old knob take it apart and look for evidence of damage or rust. You'll need to clean it off if there are any scratches or marks however, you shouldn't need to do anything major if the knob is in good working order.

Now is the time to put in the new one. First, examine the new knobs to ensure you're choosing the right one for your door. You should select one that has an extending rod that's designed to lock into the rod mechanism of the second knob. Once you've positioned the new knob over the upvc door lock replacement's hole carefully slide it into the latch.

Thread the latch plate screws down, then test the spring by pressing down several times. The latch should then spring back up every time. Then, you can install the new knob and lock it to the rod mechanism of the first knob. Then, thread the other long screws from the knob's interior through the cylinder hole on the exterior doorknob and lock it in place.

Latch

A latch is a steel piece that extends out into the doorjamb in order to hold it closed. The latch is operated via a knob or handle on the inside of the door, or by a thumb-turn on the outside. A deadbolt can be used to secure a latch and stop intruders from breaking through the glass of the door. It also protects against the accidental or deliberate closing of the door by children or pets. The latch can be fitted using one cylinder deadbolt or a double cylinder deadbolt, according to the security level you prefer.

Installing a deadbolt is the same as installing a latch, however there are some differences. To ensure that the new lock will fit, first measure the setback on the doorjamb with a tape measure. The setback is measured from the edge of doorjamb up to the middle of the hole for the latch plate. The standard setback is 2 3/8 to 2 3/4 inches. If you have a higher setback, you may need to purchase a larger latch from a hardware store or locksmith.

Then, drill a hole for the latch plate at the edge of the doorjamb. Utilize a chisel to smooth out the mortise of the latch and ensure it's deep enough for Replace Door lock the faceplate of the new latch to be flush with the doorjamb. Place the strikeplate on the floor to ensure it's placed properly.

If the strike is positioned too high, the door could be pushed in or pressure applied to it using a crowbar or tire iron. This can cause cracks to the doorjamb. This can be fixed by drilling a new hole through the doorjamb and then removing the core from the hole that was previously made.

The final step is to mount the new strike plate, which can be done by screwing it over the screw holes that are already in place. Utilize wood putty to fill in any existing holes for screws or bolts that aren't being used. Once the putty is dry you can sand it down to give it a a professional finish.

Strike

An electric strike is the metal piece where the latch and deadbolt engage when the door is shut. It is an important part of the overall security of a lock because it keeps the door shut and offers additional resistance to kicking or force applied to the door. If a door comes with an electronic strike, it can be opened only by a key and the control unit that controls its electrical impulses.

Traditionally, installing an electric strike involved cutting a section of the doorjamb to remotely remove the latchbolt of a cylindrical lock from the pocket of the strike. This modification is not only ugly and unattractive, but also exposes the latchbolt mechanism and the keeper to intruders.

Recently, a number of electric strike manufacturers have developed an innovative type of electric strike, dubbed the "No Cut" strike that doesn't need an opening in the doorjamb for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike is fitted with an internal ramp that raises the latchbolt and keeper whenever it receives a signal from a reader. The retracting of the keeper as well as latchbolt raises them on the ramp, which locks the door. When the door is shut the deadbolt remains in at a lower position and the latchbolt retracts into the keeper.

Installing an electric strike is a simple process, especially if you are replacing a patio door lock the strike on a previous door. However, if you are upgrading to an electric strike to use with an access control system, you will be required to ensure that the new system is compatible with the kind of lock you have installed. It is also necessary to make sure that the strike is properly connected to your access control system and set up to operate in a fail-safe way.

One way to protect against intrusions by thieves is to upgrade the strike on your doors to a high-quality strike plate. These plates are fitted with four to six screws of three inches instead of the two, three-fourth inch screws that are typically used in standard strikes. These longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.