• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix loose door hinge a Loose Door Hinge

Most homeowners can repair hinges that are loose. If, however, the screw holes are stripped and can't hold screws, Fix Door hinge you may need to use dowels and wood glue before you can install the hinge.

Brush away any surface rust. This will aid in keeping the dowels in place and give them a solid foundation for them to rest on.

Take the Hinges off

Most hinges on doors can be removed, which makes it easier to move the door from one side to another or take the entire door off the frame if need be. Removing the hinges is fairly easy for anyone with a little patience, although you have to know how to do it right.

If the hinges have been painted, you'll need to take off the paint prior to attempting to remove the pins. It is possible to scratch your door if you do not remove the paint. To break the paint seal, place the hinges in a stainless steel dish and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for around 30 minutes. The heat of the water will soften the paint, making it easier to remove.

After the pins are loosening and the pins are loose, you can take off the hinges from the frame and door. You can employ a screwdriver for the job done, however it is recommended that you use a magnetic screwdriver for this task. This type of screwdriver is specifically designed to take out screws made of metal and will assist you in getting the task completed much quicker.

Before you attempt to remove the hinges it is a good idea to spray them with oil. A simple lubricant can help the process to go more quickly and make it easier to remove the screws and pins. You can find this type of lubricant in most hardware and home improvement stores.

The number of hinges needed will also depend on the type of door you have and the way it's set up. Heavy bi-fold doors hinges and solid-core doors will need more hinges, while hollow-core doors that weigh less might only require two or three hinges.

Understanding the different kinds of hinges will help determine which one is best for your situation. Exterior hinges are generally designed to support the door's weight, while interior hinges will need to be able to handle heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may loosen and begin to sag or hang crookedly. This can be a problem, but it's usually easy to repair. Retightening the screw will typically resolve the issue. However, if the screw holes are stripped out, this can be more difficult. However, there is a trick to make these holes back to their original size that utilizes a wood dowel.

Start by drilling the old hole with a drill bit close to the size of the new screw (normally 3/8"). Then, you can use wood glue and a dowel made of wood to fill in the hole. To ensure a tight fit, the dowel should be cut to the same length as the screw. After that, reinstall the screw and tighten it to the desired degree of tightness. If the door still has an tendency to get stuck and close, then you can add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to make sure that the perimeter clearances are correct.

Another option is to utilize a wood plug instead of dowel. This will work as well however it may take some time to set up. Simply whittle a piece of wood to the proper size to ensure a secure fit, then press it into the hole. If you don't have a wooden tool you could also use toothpicks or wooden matches.

Make use of a countersink to make the hole smaller than the head of screw after you have put it back in place. This will prevent the screw from hitting the edge of the doors when they are closed and opened. This will allow you to tighten the screw prior to you are reinstalling the hinge.

Once you've reinstalled your hinge, make sure to grease it with a dry lubricant to prevent it from getting stuck in the future. Products like PB Blaster or Liquid Wrench are good alternatives. Apply a thin layer of it and allow it to penetrate the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're not ready to replace hinges, you could try a few fixes. Check that the screws that secure the hinge plate to the door frame and frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be cautious not to tighten the screws to the point that they begin to cause gaps at the trim joints or, even more damagingly cause threads to be stripped.

If you're experiencing issues because the hinge plates are breaking away from the door and jamb and jamb, you can Fix door hinge them by applying wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will serve as a solid base for the screws and to prevent the plates from shifting when you drive them into place. Allow the glue to dry before reattaching your hinge.

Another common cause of hinges that are loose is that screws are worn out or gone. This can be corrected by replacing the screws. Use a drill bit that is similar to the size of the screw hole to avoid drilling into the jamb or hinge.

Once you've reattached the hinge close the door and look at the gap between the door and the frame. The gap should be about the thickness of a penny or less if an old door was hung incorrectly. This should not be a problem if the hinges are properly installed.

If you notice that the hinges are loose, try adding the thicker shim of the hinge between the hinge plate and the mounting surface, to create an extra inch of space. You can also try removing the hinge pin from the troublesome hinge and pounding it down with a hammer in order to make it tighter or using an entirely new hinge pin. You can also lubricate your hinges with mineral or jojoba oil to reduce friction and help them hold their place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

The friction generated by the hinge's constant motion attracts dust particles. Without regular cleaning and lubrication, these particles get stuck in the moving parts of a hinge for doors and then build up over time. The hinge will become stiff and creaky, and its appearance can rapidly change. Regular cleaning, lubrication, and inspections can maintain the quality of door's hinges and ensure their proper function.

Check the hinges to see how much rust has formed on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace window hinges them. If you're able to save the hinges, clean any loose rust with a steel wool and wire brush. Apply a commercial rust removal solution or homemade solutions like lemon juice to the hinge. Allow the rust remover to be on the hinge for several minutes to dissolve and penetrate any remaining rust.

If you don't wish to spend the money and time replacing hinges, simply tightening the screws will restore the hinges' functionality. It may be necessary, however, to add a wooden shim or dowel to the hinge if the screw holes have been shaved. Wooden dowels come in round rods that vary in lengths and sizes. You can buy them online, at stores selling woodworking supplies and home improvement centers.

You can also make a shim from a piece metal or plastic depending on the kind of hinge you own. To make a dowel, cut a wooden dowel to the desired length. You can dip the dowel into the adhesive of a carpenter and then insert it into the hole. The glue will hold the dowel securely in the position.

Before you begin cleaning the hinges, lay down a paper or cloth towel to protect flooring and other surfaces from spills and drips that may happen. After you have protected the area clean the hinges with a soft sponge or a cloth dipped into a mild cleaner to remove dirt and grime. Also, tarnish and rust can be removed. A small or toothbrush can be used to reach difficult-to-reach spots in crevices or narrow spots.