• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are many reasons why your ignition may be stuck. One reason is that the key is dirty or has a damaged wafer inside it. You can fix this by sliding the key in and out of the cylinder many times.

Another possibility is that the pins inside the lock cylinder have become stuck. You can tap the cylinder lightly using a small tack-hammer.

Check the Battery

If your car is in Park or neutral, but doesn't come on when the key is inserted into the ignition, it might be a problem with the shifter switch for the transmission. It is possible to fix the issue by shifting the gear shifter upwards or down to get the vehicle into the correct gear.

If the car ignition switch repair still won't turn, the problem could be with the neutral safety cable or shifter in the transmission. This can be easily solved by a mechanic or an auto locksmith in your area.

It is also possible that the ignition cylinder is worn out. Over time, the ignition and the key will wear out, which causes them to become difficult to insert or remove. A lubricant, such as silicon lock grease could solve this issue, letting the wafers to slide into place.

Lint from your pocket and adhesive from tape that holds packages together can also build on the key, preventing it from being able to slide into the ignition. Clean the key using a cloth, or a cleaner such as Triflow to resolve this problem. You may also test a spare key to determine if the issue is the key or ignition.

When the key is in the ignition you can tap it with the hammer with a small amount. This can cause a slight vibration, which could be enough to loosen up the ignition's wafers and allow them to slide in place. However, you must be careful not to scratch the ignition key or cylinder.

If none of the above work, you need to call a locksmith to check the issue. It could be that the key has been damaged inside the ignition or it could be the time to replace the entire thing. If the problem is with the key the locksmith can make a new one for you. If the ignition cylinder is the issue then you'll have to bring the car to a repair shop for it to be repaired. Luckily, these problems are typically very simple to fix car ignition.

Check the steering wheel

A common issue that can hinder the ignition from turning is a locked steering wheel. This can happen if the driver has a mistake and engages it when they exit or enter the vehicle. This is usually caused by pulling on the wheel while balancing themself against it using their hands. It could also happen if someone in the back seat accidentally engages it as they get out of the car.

This is a quick solution that doesn't require an appointment with a locksmith or mechanic. First, make sure that the gear shift is in Neutral or Park. If it's not you can gently pull or push the gear shifter until it moves to one of these positions. It's also crucial to press the brake button or activate the handbrake before you attempt to turn the key.

If the wheel isn't locked taking a look at the steering column will tell whether the key is engaged with the lock. This is usually indicated by a small "Lock" label on the lower part of the ignition circle. It is easily removed by gently jiggling the lock or pulling it down with moderate force. It is crucial not to apply too much pressure, as it could damage the key or break a wafer within the lock cylinder.

Another option is to use an alternate key to see whether it is able to disengage the lock. This could mean that the original key is worn out and is no capable of engaging the wafers in the lock cylinder. A professional at Karl Chevrolet Webster City can make a new key if this is the case.

If the new key still does not engage, a short spray of penetrating oil can assist. Apply a small amount of penetrating oil to the ignition and keyhole. Then, jiggle it or tap it lightly to make sure it is working. If this does not work, you'll likely have to visit a specialist at your local auto ignition key replacement dealership. They will be able to provide you with a replacement key and also replace the ignition cylinder in case of need.

Check the Key

If you are unable get your key to turn in the ignition, it's possible that there is a problem with your key. Try taking off any foreign material on the key (lint, adhesive from packing tape, etc). You can also try rubbing the key with rubbing alcohol or Goo Gone to see if it helps.

It's possible that the lock pins inside aren't moving correctly when you insert the key. You can test an extra key by gently removing it of the ignition after having insert it. You should be capable of hearing and feeling the pins moving inside. If not, you can lubricate the pins with powdered graphite. You can purchase graphite in small tubes that can be put directly into the keyhole. This will allow the pins slide into position when you insert the key and also prevent them from getting stuck.

It is possible that your key has become damaged or worn out and isn't able to work with the pins within the ignition cylinder. This could cause the ignition cylinder to not turn and prevent you from starting your car. If this is the case you'll need bring your car to a locksmith or repair shop for service.

If you are able to turn your car using a spare key and you've ruled out any problems with the battery or steering wheel, it is possible that the ignition cylinder is been worn out. You can try to loosen the lock cylinder by using the sharp end of a screwdriver or the handle of the hammer (not the head). Sometimes, a gentle tap on the cylinder can free it and allow you to turn the key of your car. If this doesn't work, you'll need to have your lock's cylinder replaced by a mechanic.

Check the Ignition Socket

The ignition lock repair socket is where your key slides in and out when inserted. It can get clogged up with dust, or simply wear and wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to help things move forward.

You can also employ a small hammer and very gently tap the inside of the ignition cylinder in an effort to loosen or reset the pins which may be out of alignment. Be very careful to not overdo it or you may cause serious damage to the ignition switch.

It is crucial to confirm that your car's gearbox is set to park or neutral before you attempt this. Many newer cars have the ability to stop the steering wheel from turning when it is not in neutral or park and prevent the key from turning into the ignition.

If you've done all of the above and still not able to get your key to turn, it is likely that the ignition cylinder housing is in need of replacement. Different vehicles have different procedures for replacing the ignition cylinder. Therefore, it is crucial to follow the correct procedures.

This usually involves removing the plastic cover that covers the steering column and the ignition lock repair services assembly. To remove this cover, you'll need to first adjust the tilt-wheel to the lowest position and then unscrew any fasteners that are holding it in place.

Once the cover is removed, you'll have to take the old ignition cylinder off the steering column. Then, you will need to compare the new ignition cylinder that you purchased with the one that was removed to confirm that they're identical. After this, you can install the new ignition cylinder in the same way as the previous one.

It is possible that even with our best efforts, the ignition may become damaged and require to be replaced. If this happens, it's advised to contact an Tempe Locksmith for assistance. A locksmith will assist you in selecting the right replacement and install it properly to ensure that your car can start again.