• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Boarding Up a Doorway

Boarding up a doorway keeps rain, snow and hail from further destroying the property. It also keeps scavengers and vandals from the area.

Doors are more secure than windows, yet they are still susceptible to being damaged or kicked out. These doors should be set with composite frame that will not warp over time.

Take a look at the Doorway

A doorway is a hole in a wall, through which you can go in or out of the building, room or passageway. The doorway can also be a portal that provides access to a different location like an additional room within the same home or different area of the country.

To determine how big the doorway is, you'll need to take measurements. Begin by measuring the width of one side of the frame to the other with an instrument like a tape measure. It is essential to remove any brickmould or trim pieces prior to taking this measurement. This will ensure that you are only measuring the frame, not the actual windows or doors. Make use of the largest number of these measurements to determine the dimensions of the doorway.

If you're looking to replace the door, measure the width of the door's opening. It is possible to do this without removing the existing door by prying the old door away from the jamb using a wide pry tool. This will reveal the rough framing which will be used to mount the new door. Take the height of the opening in three places and use the smallest number to determine the height of the new door.

You can also determine the width of the doorway by running the tape measure along the edge of the frame in three spots in the center, left and right, and then recording the most extensive measurement as the size of the doorway. This is the most effective way to ensure that your wood will cover the entire space and permit you to put in a new door or window.

Measure the Frame

boarding up company up windows doors, windows, and other openings which let in elements can provide a measureable amount of security for your home. First, carefully inspect each window to determine the size and shape. Then, take a measurement of the width of its frame. Take note of every measurement, so that you can cut the plywood boards to the dimensions of the frame.

Before you begin, put on protective gear to guard against broken glass and other hazards. It is also recommended to work with someone else since it's easier to handle large plywood sheets with a second pair hands.

Use wide masking tape to seal the cracks and remove any panes which cannot be taped. Cover the remaining panes with heavy plastic garbage bags. You can even seal the trash bags inside out for extra strength.

If the frame is in good shape You can cut down on time by avoiding the framing and just running a new stud straight across the gap to the midpoint of the window. This will give the frame extra strength without the extra effort of removing and installing the framing itself.

Purchase a few sheets of plywood and tools such as drill, hammer and saw (if cutting is required). Mark each board in accordance with the frame's dimensions. Then, using the pilot holes you made earlier, join the plywood to the frame.

Measure the Jambs

The jambs are three pieces of wood to which a door is mounted directly. They are essential to keep doors shut properly and should be snug and level. If the existing jambs aren't, you'll need to make adjustments.

Begin with the hinge side jambs, which have a raised part toward the center that's called the doorstop. The doorstop rests on the slab of the door to keep it from hitting the frame when it closes. Attach a piece of plywood to the bottom of each stud so that it raises the floor inside the opening in about 1/2 inch (photo). This will help prevent the door from scraping against the tile, carpet or throw rug when it is shut and opened.

Remove any trim, molding or casing that is affixed to the jamb of the hinge to get an accurate measurement. This will expose the opening in rough form so that you can measure it accurately.

Mark the locations of the hinge holes on the outside and inside of the hinge jamb. Using a combination square, determine the depth of the hinge mortise and adjust the combination square until it's equal to the mark you made on the hinge jamb. This will ensure that the hinge is centered within the frame and aligned with your door. Repeat the process for [Redirect Only] the latch jamb side the door. Utilize a nail gun as well as finishing screws of 2 1/2 inches to secure the strike side.

Measure the Header

A header is a heavy dimension lumber board that is attached to the wall framing. It transfers loads above windows and doors to the studs below. When framed in properly the king studs attached to each end of the header and the jack studs butting against it on both sides create a strong support column that carries the loads from above the opening to the floor and foundation.

In traditional framed houses it is possible to use a series of tables in the code to calculate the size of the header to fit a certain span. A typical header is a double 2x12 and the code provides tables for three different widths of the building; you can interpolate for the next wider size to determine the correct size for the header.

But there are other, more efficient alternatives to the standard 2x12 header, which can reduce the need for lumber, decrease thermal bridging, and free up space for insulation. Builder Mike Guertin takes a look at these options and explains when they're the right choice:

He also talks about rim-board headers that can connect an opening in the wall without using the use of a header. This eliminates one step in the framing process and usually creates an even stronger frame. He also explains box headers, which are more difficult to build and have greater spans than single-ply. He also covers the schedule for fastening of these different headers. This calls for 8d common nail spaced every 3 inches.

Cut the Boards

Before making a decision to board up a door it is crucial to clean the area thoroughly. Get rid of furniture and other decor to give you ample work space and to avoid damaging belongings. Remove the doorknobs, locks, and other hardware and store them in a secure place to be installed later. Clean the door and frame and wipe down the surfaces to get rid of dust, dirt, and debris for better adhesion. Sand rough patches, if needed, to ensure that the boards fit securely and provide adequate protection.

Once the doorway is cleared, you can start cutting the plywood. A good circular saw will make straight cuts and cut through wood with ease and a jigsaw is able to handle curving areas. Protective equipment, such as safety goggles as well as a dust mask is crucial during this step.

It is essential to align the board with the frame and jambs when it is cut to size. It is also recommended to add some vertical pieces of lumber to the bottom of the board to provide reinforcement. After the board has been aligned and secured it is ready to be nailed in the desired position.

A doorway that is boarded up can help protect your home or business from damage and unauthorized entry during a storm, disaster or other event. It can also be used to secure a vacant property or stop thefts and break-ins until the property can be occupied. Carefully evaluating the circumstances and the need of the 24 hour boarding up service near me will aid in determining the best selection of the material and method of installation to achieve the best results.

Install the Boards

Instead of nailing the boards instead, use screws that are strong enough to fix the boards. The strength of these fasteners will distribute pressure and resist prying, enhancing the effectiveness of your boarding up property. Weatherstripping or caulk can be used to seal the edges and prevent water and wind from infiltrating through gaps. It's also recommended to leave a gap for ventilation to prevent stuffy air and moisture accumulation.

If you're using a power drill, make sure to wear gloves and goggles for safety. You should also employ a straightedge or pencil to mark your cuts, because mistakes are more difficult to correct after you're done cutting. You'll have to be as precise as you can when cutting the boards, so they're perfectly fitted against the door frame and casing. The jambs and head must be cut to ensure they're aligned with the wall.

It's best to prepare your home before the storm hits so that you will have plenty of time to cover other vulnerable areas. You will save time and effort by preparing ahead. With the proper preparation your property will be protected from criminal activity and [Redirect Only] damage caused by flying debris and winds. You can also rest in peace of mind knowing that your home is secure.