• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

You can find the perfect handle for your door, whether you are replacing your existing handles or adding security. The Upvc handles are simple to install and meet the 92mm minimum central distance for multipoint locks.

The most important measurements to take into consideration are backplate fixing centres and lever/key hole dimensions. Check these carefully against your existing measurements prior to placing an order.

Lever/Pad

Lever pad handles are made up of a lever on one side and a handle that is shaped like a paddle on the other. They are designed to be used with key wind locks. However, they can be fitted to multipoint split spindle door locks.

Once you have chosen the right handle for your doors, the available finishes will be shown in the drop-down list. Not all styles of handles are available in every finish and you should always check the technical drawings and sizes sections for the particular product you want to make sure that you can get the correct size and fit.

When choosing new lever pad door handles made of upvc, it is important to ensure that they correspond to the PZ (distance between the spindle of the handle and the centre of the cylinder hole) of your existing multipoint door locks, as they need to be in the same line to allow doors to remain locked, either from the inside or outside. The handles we sell are designed to work with a variety of standard cylinder locks, however you should double glazing window handle-check prior to purchasing.

You'll need to take off your handles that you have already installed and then dismantle the lock case if you're upgrading to dual spindle levers for your handle because this will require an additional split cylinder inline. These are available separately and we have an entire technical diagram to examine in the images for each product.

After you have removed the screws that hold the door handle you have, it is a good idea to loosen them and examine the mechanism to see the condition it is in. If the screws aren't loose enough, you may need to loosen them further. Then, you can remove the spindle from the handle and replace window handle it with a new Upvc handle. Before putting the handle in the frame, it is a good idea to check that it is in the proper place. You can do this by placing your finger in the space between the door frame and the door handle replacement handle to make sure that it is level.

Lever/Lever

Lever door handles are an a multi-point lock using a Euro Cylinder and can be found on most double glazing window handles doors made of aluminium, upvc doors and some wooden doors. They are equipped with an inside lever and an outside paddle and are generally available in two varieties. Sprung - These include a spring cassette installed within the backplate that helps bring the handle lever into the horizontal position. Non-sprung: These do NOT include a mechanism that can spring the handle lever into a horizontal position.

To fix a sagging door handle lever you'll need to locate the hole or detent access pin. It's usually small, protruding ring or rectangular found on the handle base plate. Once located you can loosen the set screw using the help of a screwdriver, and then remove it to allow the lever to return to the horizontal position.

Once the handle has been placed horizontally, you can install the screws. Tighten them to ensure that the handle remains firmly attached to the base plate. It is also advisable to apply a threadlocking adhesive to the threads of the screw to increase the grip and stop them from loosening over time.

Drooping lever door handles can be caused by a number of factors. The most common reason is that the fixings are over tightened and are putting stress on the bearings that are causing it to bind against the door face. It could also be that the levers are not being operated in a straight line and this is compressing the latch mechanism and preventing it from fully springing back into action.

Another reason is that the sprung lever isn't functioning properly and this is usually due to the spring not being in the correct position within the backplate. The simplest way to check this is to operate the handle to see if it returns to the horizontal position.

It is crucial to fix any door handles that are loose as soon as possible. This can cause excessive wear on the screws and the handle might be able to fall off the base plate. It is recommended to tighten all screws that are loose regularly in order to prevent them from becoming loose.

Lever/Snib

These handles made of upvc are called 'Snib handle sets' and feature an snib lock button located at the top of the door lever. If you do not have a dummy locking device you can use this to lock the door. These handles are fitted with a Fullex lock 68PZ. (68mm between the spindle and the centre of the lock). We also stock a variety of other 68PZ door handles from manufacturers such as Ferco and Fab & Fix.

Changing your door handle is a cost-effective method to upgrade your home, whether you're replacing handles that are in use or fitting new ones on doors you've constructed in your home. There are a variety of styles of door handles made of upvc, including traditional lever on backplates, straight or curved short latches, and knob handles that resemble dummy knobs for multi point locks, that are perfect for French bi-fold doors handles.

Rose door handles are circular or oval-shaped versions of backplate lever handles. These handles for doors are identified by a lever or knob that is attached to a backplate. The backplate is removable for concealed fixing.

The handles are available in a variety of finishes, including chrome and coloured finishes, to complement your door and other hardware like knobs, bolts and hinges. Some handles come with grub screw to attach the knob or lever to the spindle. Some handles come with bathroom spindles which are suitable for bathroom locks. They also come with an release mechanism that turns the thumb and can be used on doors for bathrooms.

Mortise

If your front door's uPVC handle is stuck in the open position, the problem will most likely be with the tubular latch. It could be due to various reasons but the most prevalent is an absence of lubrication within the latch plate. This can be corrected quickly by opening the door and spraying lubricant on the handle and lock. Or, it could be that the latch plate has become detached from the backplate. This can be a bit more of a problem and would require a professional to fix it.

A multipoint handle system is the best solution for stuck door handles. These handles are attached to the faceplate and operated with the use of a key or thumb turn knob that triggers the cam that locks the deadbolt. The handles are available in a number of different sizes to fit various kinds of uPVC doors. They are also available with a variety of attractive finishes that match the hardware you already have. The handles can be bought via the internet or from an authorized locksmith in your area. They are easy to install with clear instructions.

If you want to replace the handle set, you'll need to determine the PZ dimension of your cylinder. This is the distance from the edge of the frame of the door to the central point of the hole for the handle in millimetres. You will also need to know if your door has hook-style locks or a mortise style lock. Once you know these measurements, the easiest method to determine the right handles is to use the filter by brand option on the website. This will help narrow down your options, and then you'll be able to select the appropriate size.

A typical handle set includes the handle, a pair of different length screws drilling guides, as well as installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ come with a mortice lock with a keypad. These are more complex models and are ideal for professionals who install them or competent DIYers. Certain handle sets come with a range of other accessories, such as weather strips, which can be used to enhance the appearance of the door.