• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. However, if the screw holes are damaged and won't hold screws you may need to use dowels and wood glue before you can install the hinge.

Clean up any surface rust. This will allow the dowels to stay in place and give them a solid foundation to hold onto.

Remove the Hinges

Many standard door hinges can be removed, making it simpler to move the door from one end of the frame to the opposite side or take the entire door off in the event of need. Removing the hinges is fairly simple for anyone with a bit of patience, but you need to know how to adjust upvc window hinges do it right.

If the hinges are painted, you'll need to get rid of the paint prior to attempting to remove the pins. If you don't, the paint will be smashed off and scratch your door when you try to lift it. To break the seal put the hinges into a stainless steel dish and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for around 30 minutes. The heat from the water will soften the paint making it easier to take off.

After the pins have been loose, remove the hinges and frame from the door. It is possible to use a regular screwdriver, however you should use a magnetic screwdriver for this project. This type of screwdriver has been specifically designed to grab screws made of metal and will assist you in getting the task done much faster.

Before you attempt to remove the hinges, it is recommended to spray them with some lubricant. A simple lubricant will help you move the process along faster and also remove the screws and pins easier. You can find this type of lubricant in most hardware and home improvement stores.

The number of hinges required will also depend on the kind of door you have and how it is set up. Heavier and solid-cored doors will require more buy upvc window hinges whereas lighter and hollow-cored doors may only need two or three.

Understanding the various types of hinges can help you decide which one is the best for your particular situation. The hinges on the exterior are designed to hold the weight of a door, while interior hinges must be able to handle heavier loads.

Reattaching the Hinges

Over time, the hinges of doors may lose its grip and then begin to slide or hang crookedly. This can cause problems but is usually easy to fix. Retightening the screw will typically solve the issue. If the screw holes have been stripped out, it may be difficult to fix. Fortunately, there is a trick to make these holes tight again that uses a wood dowel.

Begin by drilling out the hole you had previously made using a drill bit that is similar to the size of the new screw (typically 3/8"). Then, use a wood glue as well as dowels made of wood to fill the hole. To ensure a secure fit, the dowel should be cut at the same length as the screw. Reinstall the screw, and tighten to desired degree of tightness. If the door continues to bind up, insert a second dowel to the gap. Repeat the process. Make sure to close the door slowly to check the perimeter clearances after each adjustment.

Another option is to just make use of an old-fashioned wood plug instead of a dowel. It's also possible, but may take some time to set up. You can use the wood piece that has been whittled down to the right size. If you don't have a woodworking tool You can also make use of toothpicks or wooden matches.

After you've reinstalled your new screw, use a countersink bit to make the hole for the head of the screw smaller so that it does not rub against the edge of the door when it is opened and closed. This will aid in tightening the screw prior to reinstalling the window hinge replacement.

After you have reinstalled the hinge, be sure to grease it with a dry lubricant to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin coat and allow it to take approximately 15 minutes to get into the hinge barrel.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you are able to make a few minor repairs. Verify that the screws that secure the window hinge repairs near me plate in place to the door frame and the frame are in good condition. If they're loose, tighten them using the help of a screwdriver or a power drill. Be cautious not to tighten the screws to the point that they begin to cause gaps at the trim joints, or even worse cause threads to be stripped.

If the problem is the hinge plates are splitting and you want to reattach the plates by applying wood glue to the back of them and then inserting toothpicks or wooden dowels into the holes. The dowels or toothpicks provide a solid base for the screws and keep the plates from moving when you drive them into the holes. Allow the glue to dry before reattaching the hinge.

The screws could also be damaged or missing. This issue can be resolved by replacing the screws. Be sure to use the correct drill bit for the size of the screw hole to avoid drilling into other parts of the jamb or hinge.

Close the door once you have reattached your hinge and examine the gap between the frame and the door. The gap should be the thickness of a penny or less if an older door was hung incorrectly. This shouldn't be a problem if hinges are properly installed.

If the hinges still seem loose, try adding a thicker hinge between the surface of the hinge plate and the mounting surface. This will give the hinges more room. You could also try removing the hinge pin from the problem hinge and pounding it using a hammer to make it more secure or using an entirely new hinge pin. It is also possible to lubricate the hinges using mineral or jojoba oil to lessen friction and aid in holding their position. Lubricating your hinges periodically can keep them from becoming stiff and squeaky and can also prolong their life.

Cleaning the Hinges

The friction generated by the constant movement of a hinge attracts dust particles. Without periodic cleaning and lubrication, the particles become stuck in the moving parts of a hinge for doors and then build up over time. As a result the hinge can become stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspections will maintain the functionality and quality of hinges that are attached to doors.

Check the hinges to see how much rust has formed on their surfaces. If the corrosion has reached the point of destroying the surface of the barrel or screw holes, you'll require replacement hinges for double glazed windows of the hinges. If you can save the hinges, you can remove any loose rust by using wire brush and steel wool. Then apply a rust remover from a commercial store or a homemade solution such as lemon juice on the hinge. Allow the rust remover to remain on the hinge for a few minutes to penetrate and dissolve any remaining rust.

Retightening screws can help restore hinge functionality if you don't want to spend time or money to replace hinges. It is possible, however, to add dowel or shim made of wood to the hinge in the event that the screws have been degraded. Wooden dowels are round pieces made of wood in the shape of rods that are available in varying sizes and lengths. They are available at home improvement stores, woodworking supply and craft shops, or online.

A shim could also be made from a piece of metal or plastic, depending on the kind of hinge you have. To make a dowel cut an unfinished dowel into the desired length. Then, dip a dowel into carpenter's adhesive and place it in the hole. The glue will hold the dowel securely in the desired position.

Before you start cleaning the hinges, place down a cloth or paper towel to shield floors and other surfaces from drips and spills that could happen. Once the area is protected then clean the hinges using a soft sponge or cloth that has been soaked in mild cleaner or vinegar to remove the build-up of dirt, grime and tarnish. You can use a toothbrush or small brush to reach hard-to-reach spots in crevices or tight areas.