• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive way to increase the security of your home. However, this procedure isn't for all. It requires a certain amount of skill and perseverance.

The cylinder is inside the knob's body. The cylinder recognizes the key when it is put into the lock.

Removal of the old lock

The first step in replacing the door lock is to remove the old lock. It's a fairly simple process, but there are a few points to be aware of. First, make sure that the lock you choose to install is the correct size for your door. This will ensure that it fits properly and does not leave a gap in the latch or deadbolt plug.

After you have removed the latch plate, you will be required to search for two bolts or screws on the inside of casing that are holding the casing to the lock halves. Unscrew these with the help of a screwdriver, and then pull the lock out of the door. If you have a mortise locking mechanism, there is an anchor screw that connects the handle to the spindle. Make use of a screwdriver for removing the screw, and then take out the doorknobs.

It is also recommended to take the deadbolt and latch plug from the hole in your door jamb. Install your new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the edge of your door to ensure that your new lock will be able to fit.

There are a variety of reasons that could prompt you to replace your door lock, such as believing that someone else has the key or welcoming a new roommate. In any case, you can save money by taking the lock off yourself, rather than hiring an expert to remove it. It's easier than many people think, and it can be completed in a few minutes.

Start by getting rid of the handle and trim from the door. Then, pull the trim away using a screwdriver that is flat. You will be able to pull off the majority of it and in some cases, the handles might come off completely. The next step is to look for a hole on the inside of the handle and then insert straightened clips into it. This will activate the release mechanism, which allows you to take off the handle. Next, examine the interior side of the lock for another small tab and press it using a screwdriver that is flat. Once the spindle is removed, you are able to remove the cylinder and housing.

Selecting a new lock

When it comes time to pick a new lock you have a variety of choices. Think about the various kinds of window locks Repair and pick one that fits the design of your door. Think about the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Select a lock that will fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give you an idea of their durability and how difficult it is to pick them or disable them. A grade 3 double glazed window lock repairs near me could be the best choice for a peaceful rural apartment complex, while a grade 1 lock might hold up better to the traffic near a busy storefront on a busy city street.

Most smart door locks require a digital code to open. If you're worried about hacking, or any other security concerns, speak to a professional locksmith.

Replace the cylinder

If your door lock cylinder is damaged or broken it can be replaced in a matter of minutes using a simple DIY project. It is essential to choose the appropriate cylinder and follow all instructions. First, you must remove the handle or knob if it is present. Then with a screwdriver take off the trim around the lock cylinder. After the trim is removed, you will be able to access the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently pulled out of the door.

Be sure to measure the length of your new cylinder before installing it. Take a measurement of the distance from the center to the right and left sides of the cylinder with an instrument. Purchase a new cylinder which has the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.

Insert the replacement window locks cylinder in the door, and then turn the key. This will align the cylinder with the carrier that is usually located on the outside of your lock. Then, loosen the set screw that should be just a couple of turns in the head. If there is a screw at the edge of the case that is holding the door, you'll need to remove it.

You can replace the old lock cylinder with the new one by slipping it into the case and then tightening the set screws. You should also reinstall the piece that connects the cylinder to the stem of the lock indicator that you can do by pulling out three small tabs on the back of the cylinder with needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you should reinstall the strike plate and latch plate as well as the retaining ring that is connected to the top of the lock the cylinder.

Installing a new lock

Begin by measuring the door's width if you are replacing an existing window lock repair near me. The majority of residential locksets are designed for a door thickness of 1 3/8 to 1 3/4 inch. If your door is more thick you will require an extra-thick door kit that includes longer screws and a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come equipped with a thorough installation guide to help you. Before you begin, go through the instructions to ensure that you have followed all the steps. The manual will also give you an idea of the level of skill required to complete the task. If you're replacing a lock for the first time, you may consider asking a more experienced friend for assistance.

It's a great idea to seal the openings of the old lock before installing the new lock. This will prevent the screws from falling through the holes and will also protect any tiles you may have installed. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used to protect your painter's tape, but you can also use gaffer's tape or masking tape if you have it available.

Once you've removed the screws holding the inside of the lock section to the outside side, pull it straight away. It's important to do this swiftly to avoid the lock from accidentally closing itself and damage the mechanism.

Install the new latch bolt into the upper cross bore of the new lock, if it comes with one. Be sure to put it in the right position as indicated by an arrow on the faceplate. Then, slide the latch plate onto the bolt and screw it into place.

Screw the deadbolt to the jamb on the door. Test the deadbolt a few times, throwing it around to make sure it extends into the strike plate. Follow the instructions that come with your electronic smart lock to program it. This involves downloading an application, entering your email address, confirming your identity, and accessing the wireless network to connect your device.