• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is a simple and affordable way to improve the security of your home. This process isn't for everyone. It requires some expertise Window and door Lock repair perseverance.

It is necessary to replace the cylinder, which is located inside the knob's body. The cylinder recognizes the key once it's placed into the lock.

Removing the old lock

The first step to replace a door lock is to remove the old one. It's a fairly simple process, but there are a few things to remember. Make sure the new lock fits your door. This will ensure that it is securely fitted and won't leave a gap at the deadbolt or latch.

Once you have removed the latch plate look for two bolts or screws on the inside of the casing that secure the casing and halves of the lock. Remove them with a screwdriver, then pull the lock out of the door. If you have a mortise locking, there could be a set screw located at the base of the handle that holds it to the spindle. Take off the doorknobs by removing the screw using a screwdriver.

Remove the deadbolt and latch plug from your door jamb. Then, you can put in your new lock. If you are replacing a mortise you should measure the distance between the lock case and the door edge to make sure that the new lock will fit.

You might want to change your lock for a variety of reasons, for instance, the possibility that someone else holds the key or you've new roommates. In any event, you can save money by removing the lock yourself, rather than hiring a professional to do it. The process is simpler than many people think, and it can be completed in a few minutes.

Remove the trim and handle from your door. Then, you can pry the trim loose with a flat screwdriver. You will be able to pull off most of it, and in some instances the handles may fall off completely. Next, examine the handle for a tiny hole on the inside. Then insert a straightened paper clip into it. This will activate the release mechanism, allowing you to remove the handle. Then, look for a small tab in the interior of the lock and press it with a flat screwdriver. Once the spindle has been removed, you are able to remove the cylinder and the housing.

The choice of a new locking system

You have many options when it comes to choosing a new lock. Consider different kinds of locks, and find one that matches the style of your window door lock repair. Take into consideration the backset which is the distance between the edge and the center of the hole for the lock. Also, think about the cross bore, a tiny hole that is located at the edge of your door's frame. Also, make sure to select a lock that is able to accommodate the door's thickness as well as swing.

Most door locks have been evaluated by BHMA and the American National Standards Institute to provide you with an idea of how well they are able to withstand the rigors of use and how difficult they are to disable or pick. A lock grade 3 might be the ideal choice for a tranquil apartment building in a rural area, whereas locks that are grade 1 might be more suitable for an area with a lot of traffic, such as a storefront.

Most smart door locks require a digital code to open. If you're worried about hacking, or any other security concerns, consult a professional locksmith.

replace window lock the cylinder

If your door lock's cylinder is damaged or broken you can repair it in just a few minutes using a simple DIY project. The trick is to select the right cylinder, and follow the instructions that accompany it. The first step is to take off the handle or knob if there is one, then unscrew the trim that is attached to the base of the lock cylinder by using a screwdriver. After the trim is removed, you can access the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently pulled away from the door.

Before installing the new cylinder, you must make sure that it's the correct length for your door. Measure the distance from the center to the left and right sides of the cylinder using an instrument. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when the door is kicked or the key becomes stuck inside.

Place the replacement window locks cylinder inside the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is typically located on the outside of the lock. Then, loosen the set screws that should be a couple of turns in the head. It is also necessary to loosen the screw at the door's edge that holds the case in place, if there is one.

After you have removed the lock cylinder after which you can replace window lock it with the new lock by sliding the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder to the stem for the lock indicator and this can be done by removing three small tabs on the back of the cylinder with needle-nose pliers. Attach the smaller bracket to the cylinder's back. You should then reinstall the strike plate and latch plate, as well as the retaining rings fixed to the top of the lock the cylinder.

Installing a new lock

Start by measuring the door's width if are replacing an existing lock. The majority of residential locksets have a thickness of 3/8 inch to 1 3/4 inches. If your door is more than 1 3/8 to 1 3/4 inches, you'll require a stronger door kit. This will require longer screws and either an extended spindle extension or tail piece for door knobs.

The majority of locks come with a detailed instruction booklet to help you install the new hardware. Be sure to read the instructions thoroughly before starting the process to ensure that you are following all of the necessary steps. The guide will also give you an idea of the level of skill required to complete the task. It is possible to ask a person who has worked with locks for assistance if are changing locks for the first time.

Before installing the new lock it is a good idea to cover the openings with tape the old hardware. This will stop the screws from falling through the holes and will also protect any tiles you may have installed. It also shields your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape, but you can make use of any tape you have.

Once you've removed the screws holding the inside of the lock section to the exterior side then pull it out straight away. This must be done quickly to prevent the lock from closing accidentally and damaging the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock if it has one. Make sure that you place it in the right location, which is indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Screw the deadbolt into the jamb on the door. Test the deadbolt by throwing it a few times to verify that it is extended all the way to the strike plate and is fully secured. Follow the instructions that come with your electronic smart lock to program it. This involves downloading an application and registering your email address, confirming your identity, and accessing the wireless network to add your device.