• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first protection is your door lock. It will stop unauthorized entry into your home. Locks may require replacement because of signs of wear and tear or other events like moving into a new house or a burglary.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to purchase the right-sized lock.

Deadbolt

If you want to make sure your door is secure from criminals, it's a great idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe, it makes it harder for an intruder to break through the door. A single-cylinder deadbolt is activated using a key on the outside and a thumb-turn piece situated inside. Deadbolts can only function only if it is correctly installed.

The first step is to find out if the door has a hole to install deadbolts or needs to be bored out. Mark the position of the hole for the deadbolt on the exterior of the door using the template included with your lock installation set. Utilize your tape measure to determine the height of the deadbolt. Then, mark the height on the side of the door. Use a speed square to draw straight lines across the mark you made for the bolt hole.

Then by using the power drill, drill through the hole until it is on the opposite side of the door. This may take some time. Sand the hole and the door edge to make it smooth. At this point, it's a good idea also to stain or paint your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assembly of the deadbolt, as well as the bolt that is inside. Then, remove the bolt and replace it with a new bolt that matches your door hardware. The bolt is typically connected to a setplate that you have to remove. After that it is time to cut out the space for the strike plate that is on the door frame.

If your strike plate is misaligned, it's likely because the previous installer didn't properly mortise it or a weatherstripping was installed and altered the strike position. To correct this issue, you will need to remortise the strike plate and the deadbolt. Close and lock the deadbolt after you have completed this step. Be sure the bolt is extending into the strike plate and then test the key to make sure it closes and opens easily.

Knob

It could make your home or business less secure if the door knob is damaged. It could also make opening and closing the door more difficult, which is why it is an ideal idea to replace door lock the knob. replacing lock on upvc door the knob is an easy DIY task that should not take less than 30 minutes to complete. You can use a screwdriver and pliers to take off the knob or handle However, be careful not to harm any of the other components on the upvc door replacement lock.

Before starting you'll need to spray WD-40 or another dry lubricant onto the mechanism of the knob for your door. This will assist the new lock to slide smoothly as you turn it. It's important to use a quality knob and handle that match your current doors to ensure that the lock is operating properly. If you don't already have a doorknob that matches and handle, you'll need to buy a upvc replacement door locks.

Before you begin the replacement, examine the old knob to determine which screws are keeping it in place. If there aren't any screws you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and remove it.

After you've removed your knob, check it for any signs of rust or damage. You'll have to scrub it up if there are any scratches or marks however, you shouldn't need to do anything If the knob is in good shape.

Now it's time to install the new one. Before you do that, look over the knobs you've chosen to ensure you're selecting the correct one for your door. You'll need to pick one with an extender rod that is interlocked with the rod mechanism of the second knob. After you've placed the new knob in the hole in the door, carefully insert it into the latch.

Thread the latch plate screws down and then test the spring by pushing down several times. The latch should spring up each time. Then, put in the new knob and interlock it to the rod mechanism on the first knob. Thread the long screws of the interior doorknob into the cylinder holes on the exterior knob and lock it into its place.

Latch

A latch is a metallic piece that extends into the doorjamb to keep it shut. It is operated with a knob or handle on the interior side of the door or a thumb turn on the outside side of the door. A deadbolt is a device used to secure a latch and stop burglars from piercing the glass of the door. It also protects against accidental or intentional closing of the door by pets or children. You can choose to install an entry point with either a single-cylinder deadbolt or double-cylinder deadbolt, depending on your preferred level of security.

Installing a latch involves the same steps similar to installing a deadbolt however there are some variations. To make sure that the new lock will work first, take a measurement of the setback on the doorjamb with an instrument such as a tape measure. The setback is the distance from the edge of the doorjamb to the middle of the hole for the faceplate of the latch. A typical setback is 2 3/8 to 2 3/4 inches. If you have a greater setback, you might need to purchase a more substantial latch at a hardware store or locksmith.

Then, make a hole for a latch plate in the edge of the doorjamb. Use a chisel and cut the mortise of the latch. Make sure the hole's depth is enough to allow the faceplate to be flush with the doorjamb. Tape the strikeplate in place to ensure it's placed properly.

If the strike is placed too high, the door may be pushed into or pressure imposed on it with a crowbar or tire iron. This can cause the doorjamb to break. This can be repaired by drilling a new hole in the doorjamb, and chiseling the core out of the old one.

Installing the new strike plate is the last step. This can be done by screwing the new plate over the screw holes that are already in place. Use wood putty then to fill in any existing bolt holes or replace Door lock screw holes that aren't being used. When the putty is dry then sand it to a smooth finish for a professional finish.

Strike

The metal piece that engages the deadbolt and latch when the door is closed is an electric strike. It is an essential part of the lock's overall security because it prevents the door replace door lock from opening, and also provides additional resistance to force or kick. If a door has been equipped with an electric strike, it can be opened by a key or the control unit which controls the electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a piece of a doorjamb, which would let the latchbolt of a cylindrical lock from the pocket inside the strike. This change can be an inconvenience in terms of the appearance of openings and also exposes the keeper mechanism and latchbolt to any unauthorised users.

Recently, a number of electric strike makers have come up with an innovative type of electric strike dubbed the "No Cut" strike that doesn't require an opening in the doorjamb for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without damaging the doorjamb's faceplate.

The strike has an internal ramp that raises the latchbolt and keeper when it receives a signal from the reader. The keeper and latchbolt are pushed higher on the ramp thanks to the retraction. When the door is closed the deadbolt remains retracted, and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward procedure, especially in the case of replacing upvc door lock an existing strike. If you're planning to upgrade an access control system to an electric strike, you need to ensure that your new system is compatible. You will also need to ensure that the strike is properly wired to your access control system and is set up for fail-safe operation.

Upgrade your strike plates to high duty strike plates to prevent unauthorized entry. The plates are made of up to six screws of three inches instead of two screws of three-fourths inch. These screws are longer, making it more difficult for someone to break the frame and then reach inside to turn the piece that turns the thumb of a single deadbolt cylinder.