• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

Over time the handles on your doors will wear out and require replacement. It is essential to be able to match the dimensions of the handles that were previously used when replacing them.

The top screw's position as well as the lever and keyhole size are the three measurements that you need to determine. Use the size guide to assist you.

Inline Lever/Lever

A lever/lever handle is a modern door handle that is designed to fit new or replacement doors. This type door handle is offered in a wide range of designs and finishes. This handle is available from several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles of uPVC/Composite are constructed of durable materials and are ideal for multi-point lock doors that require a heavy duty design. The handles are inline and work from the same spindle and screw fixings so they can be easily incorporated into existing or new uPVC/Composite doors.

The sprung lever design allows the handle to be placed and angled to ensure a comfortable experience and is suitable for all users. The handle has been endurance tested to 200,000 cycles, which helps to ensure the quality of the finish and performance of the handle over time. The sprung lever can also be cut to fit more locks. This is especially useful for narrower door frames where the cylinder is further back. A shorter lever is a good choice for doors where the latch can be operated by a thumb turn located on the inside.

Lever Pad

The lever pad upvc handle is different from the lever handles that are commonly found on doors. These handles are operated by a single spindle or by two spindles, inline or offset. They are typically employed on UPVC double glazing handles glazed doors and are available in a variety of variations and finishes.

The handles are available in various finishes, including white window handles, Chrome, and Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.

All UPVC lever pads for handles include a spindle and screws and can be mounted on a uPVC door. The backplate fixation centres of 211mm permit a larger handle, which is usually an advantage when replacing a damaged or old multi-point door sash lock door handles mechanism. The handle levers come with a spring, which solves the problem of door handles that sag out of the horizontal position when not being used.

It is important to match the PZ dimensions of both the multipoint lock as well as the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement may also be referred to as 'handle centres or cylinder centre'. It is important to match the correct handles.

Once you have the proper PZ size you will then have to ensure that the lever pads and push pads are of a suitable shape for the American with Disabilities Act (ADA) compliant handles that you require for your doors. These are typically round or square with an internal lever and an external push pad.

Most of the UPVC lever pads we sell are sprung, meaning that they return to their horizontal position when they are not being used, instead of hanging out and potentially sticking in the frame. This keeps draughts out of the home. It is also the case that the majority of UPVC lever pad window handles are hand-operated that allows you to put them on either side of the door.

Euro Cylinder

Cylinder locks can be found on uPVC and other kinds of doors. Cylinder locks are operated by using a key that unlocks the cylinder's case. This exposes pins that can be aligned with those inside the lock and allow them to rotate the revolving camera, opening the door. Euro cylinders can be fitted with up to six pins, with internal and external doors usually requiring different levels of security.

The choice of cylinder is essential. It is based on the type of use your doors and handles will receive. Doors that are external, for instance are required to be fitted with higher security cylinders while internal doors can be secured using an ordinary cylinder. Some cylinders have extra features that increase security, for instance, anti drill or anti bump properties.

A euro cylinder must be measured correctly to ensure that it is the right size for your door. The cylinder must be measured from the central screw hole to the ends of the cylinder. This includes the thumb turn, in the event that one is present. If you are unable measure it using the lock in its position, you can take it out of it. A cylinder that protrudes beyond the handle and escutcheon might be vulnerable to attacks, such as lock snapping, so it is essential to make sure it's not too long.

The design of the latest cylinders has anti-drilling and bump resistance features. They are designed to minimize the chance of attack by forcing cylinders to turn in a different direction. This can to deflect attacks and ensure your door is secure.

There are cylinders that have been made to withstand snapping. This is a growing kind of attack on cylinders where the break line inside the sash lock door handles is targeted by a tool that is specially designed to snap off the front of the cylinder and allow the door to open. This is much quicker and more straightforward than opening a multipoint lock and leaves little evidence of a break-in, which can impede an insurance claim.

Spring Cassette

The spring cassette is situated in the base plate of the door handle. It is a spring-loaded solution to bring your multipoint lock handles back to their resting position after use. These handles used to have no spring, and would slide when the locking mechanism was disengaged. This simple part is the best way to solve this issue. It also stops your door from becoming stuck in either the open or closed position, as they are difficult to close manually.

These spring cassettes have been specifically designed to be used with sprung multipoint locks They will not work with non-sprung multipoint handles. You will need to have a custom hole cut into your backplate to allow these to fit (please check the image for a technical diagram). They are a replacement for broken or missing cassettes in the backplates of door handles of various brands of uPVC doors. They feature a square cut-out that allows for an 8mm spindle to be used and they are supplied individually.

These spring cassettes are an excellent value solution to the problem of door handles that have become sagging. They are simple to install and will extend the life of your uPVC door. For more information about our selection of uPVC accessories and spares, contact us today. in touch with our team. We are always ready to provide expert advice and to assist you.