• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio door wear and tear can cause lock malfunctions. Fortunately, there are several simple and efficient ways to restore your uPVC patio door's security.

These quick fixes will make your home safer no matter if you adjust the lock or clean the mechanism.

Clean the Lock

Although patio doors are a great way to bring the outside in and keep out the elements, they can also be an issue for security if your lock isn't working as it should. With time wear and tear hot and cold weather, dirt and debris can affect the lock of your patio door and cause it to become difficult to open. With a little attention, you can make sure that your patio door's lock always works correctly.

It's important to first clean the patio door lock as well as all moving parts. This will help get rid of any dirt or coatings that could be preventing your lock from functioning effectively. Begin by wiping down all the moving parts on the lock for your patio door with a wet cloth. Then you can use a scouring paper or rough damp cloth to scrub the areas that are soiled of the door and frame. Then, wipe the lock down with a dry cloth to get rid of any moisture. Allow it to air-dry before you use it.

If your patio door has pin-tumbler latches, you can lubricate it by applying powdered Graphite to the key. You can also use a Teflon oil like WD-40 Multi Use Product. This type of lubricant can be applied with ease and does not dissolve over time. If you're unable to find the right lubricant for your lock, make use of a pencil with a thicker tip. Insert the pencil in the lock, then shake it to distribute the graphite.

Sliding patio screen door repair near me door tracks also require regular maintenance to keep them free of dust, dirt and other debris. They are particularly susceptible to ice, snow, and other debris, which could cause them to block or become stuck. This can make it difficult for your patio door to open and shut.

Tracks for sliding patio doors and rollers can be cleaned by removing any dirty or damaged weather stripping and then cleaning it, before installing it. The same applies for patio door rollers, which can be cleaned and sprayed with a non-stick lubricant that will allow them to move freely.

Lubricate the Moving Parts

uPVC french doors, like sliding patio doors, work with 3-4 or sometimes five-point locking mechanisms, which include the handle and lock cylinder operated by a key. They also require maintenance, including lubrication of the moving parts. This can be done using a thin oil however, never WD40. It should be done at least once per year.

If hinges that are sagging don't cause the issue, it could be that the door isn't aligned. It may be rubbing against or catching the hole of the strike plate in the frame. The solution is to remove the strike plate, and then use a sharp chisel to enlarge the mortise it sits in. This will permit the latch to fit properly into the hole and prevent it from scratching against the frame.

Once the cylinder is cleared of the way tilt and slide patio door repairs out of the way, measure its width using a book or piece of wood that fits into the gap of adjustment screw above the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner measurement runs from the center of the adjustment screw to the end of the cylinder.

Verify the lock's width

If your patio sliding door repair near me door latch isn't able to turn even after cleaning and lubricating, it's possible that it is out of alignment with the strike plate hole. Verify that the door is properly balanced and if the hinge screws are secure However, in many cases shifting the strike plate upwards or downwards can correct the issue.

Oftentimes, the problem occurs when the lock's strike is too small for the latch to engage. In this case, enlarge the opening with a chisel and hammer. Then test the latch to ensure it doesn't rub against the jamb frame of the door or fall the frame.

Before buying a replacement lock, it is important to identify the type of mortise lock you currently have. This can be done by looking at the end faceplate and noting whether it is round or square. Then, look at the screw holes in the existing lock and note the dimensions of each. This information will help you find a replacement that is the same size and fits perfectly into the hole that you already have.

In addition to identifying the current mortise lock, you'll also need to check it for any nicks or bends that may need repairing. A badly damaged or bent latch is more likely to break than one that hasn't been used much, so be sure to replace the lock with a new, secure version when you spot any indications of damage or wear.

Once you've identified the type of lock replacement that you require, it's now time to start the actual repair. Remove the old handle and spindle out of your patio door, and then install the new one. Begin by installing the interior handle by aligning it with the spindle and then fixing it with the two bolts or screws that hold it. Install the exterior handle following the interior handle. After you've completed these steps you can test the new handles to ensure that they open and close easily and that the latch is catching correctly when you strike the plate.

Make sure you check the Strike of the door.

The door latch and strike plate are the two parts of the lock that work to ensure that the latch is secure the door. A misaligned strike plate or door latches will cause the latch to not latch the door properly. Fortunately, this problem is usually simple to fix.

Check the receiving holes of the strike plate to ensure they are free of obstructions, such as dirt or plastic plugs. Then loosen the screws that secure the strike plate in place and allow it to move vertically, but not detaching it from the frame of your door. Adjust the strike plate so that it aligns its receiving holes with the latch hooks of the door latch. After the strike plate has been adjusted then tighten all screws, and test whether the door shuts smoothly.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are vital to lock and unlock your door. The metal plates are typically located on the top and bottom of the door jamb where they support the door's latch. The door latch is placed on the strike plate, creating the seal when it is closed. If the strike plate is damaged, rusted, or not properly installed, it could hinder the latch from locking the door securely.

One common reason for the patio door lock to become stuck or not close is a misalignment between the latch and strike plate. The easiest way to check for this is with the "lipstick test." Apply some lipstick on the edge of the deadbolt, then put masking tape on it. When you shut the door the lipstick will leave an impression on the tape that will show you exactly where the latch meets the strike plate. If the mark is too high or low it is possible to adjust the strike plate.

The sliding patio door locks protect your home from burglars. If they're not working correctly, you must solve the issue fast. Follow these easy steps to repair your patio door lock and restore it's functionality.