• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors wear out with time and require to be replaced. When replacing a window handle them, it is important that the new handles conform to the critical dimensions of the previous handle.

The top screw's position, the lever and the keyhole dimensions are the three measurements you have to check. Use the size guide to assistance with this.

Inline Lever/Lever

A lever/lever handle is a contemporary door handle designed to work with new or replacement doors. This kind door handle is offered in a variety of styles & finishes. This handle is offered by a number of manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite handles are made from durable materials, and are perfect for doors with multiple points that require a strong design. The handles are inline, and use the same spindle and screws to fix them. They can be easily installed on new or existing uPVC/Composite door.

The handle for double glazed window can be positioned and angled to suit any user. The handle has been tested for endurance up to 200,000 cycles, which allows for the assurance of the quality of the finish and performance of the handle over time. The sprung lever is also adjustable to fit a wide range of locks. This is particularly useful in doors that are narrower, where the cylinder is further back from the door. A lever that is shorter can be used for doors that have a latch which can be operated with the thumb inside.

Lever Pad

A Lever Pad upvc door handle operates differently than lever handles found on most doors. These handles are operated by one spindle, or two spindles inline or offset. They are usually utilized on UPVC doors with double glazing. They are available in a variety of finishes and variations.

The handles are available in various finishes, including White, Chrome and Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This provides the handle with a high performance and durability for its intended use.

All UPVC lever pads for handles include a spindle and screws and can be installed on a uPVC door. The backplate fixing centres of 211mm allow for a larger size handle that can often be a benefit when replacing a faulty or worn multi point door lock mechanism. The handle levers are spring-loaded, which solves the issue of door handles sagging out of the horizontal position when they are not in use.

When selecting a replacement UPVC handle and spindle, it is crucial to match the dimensions of the PZ on both the multipoint lock and the uPVC door. This measurement is often referred to as the 'handle centre' or 'cylinder centres and is an essential aspect of matching up the right handles.

When you have the right PZ size you will then be required to make sure that the handle lever pads and push pads are a appropriate shape to accommodate the American with Disabilities Act (ADA) compatible handles you require for your doors. They typically have a square or round shape with an internal lever and an external push pad.

Most of the UPVC lever pads that we sell are sprung, meaning that they return to their horizontal position after not being used, instead of hanging out and potentially sticking in the frame. This helps prevent the draughts and cold air from entering a property. The majority of UPVC lever pad handles are available in left and right handed models that allow them to be put on either side of doors.

Euro Cylinder

Cylinder locks are usually used on uPVC doors, but can be utilized on other types of window handles of doors. The cylinder lock operates with a key that unlocks the cylinder's case. The case is then able to reveal pins that can be aligned to those in the lock and allow them to rotate the camera that rotates, opening the door. Euro cylinders can be equipped with up to six pins, with external and internal doors usually needing different levels of security.

Choosing the right cylinder is essential; it is dependent on the way your door and handle are utilized. For instance, doors that are external require an extra secure cylinder, whilst internal doors can be secured with a standard cylinder. In addition, some cylinders have extra features which can enhance security, for instance anti-drill and anti-bump characteristics.

A euro cylinder must be measured correctly to ensure that it is the correct size for your door. The cylinder should be measured from the hole for fixing screws in the middle to the end of the cylinder including the thumb turn if you have one. If you are unable measure it using the lock in a fixed position, you can remove it. A cylinder that is protruding beyond the handle and escutcheon might be susceptible to attacks like snapping locks, therefore it is essential that it is not too long.

The design of the latest cylinders has anti-drilling and bump resistance features. These are designed to reduce the chances of an attack by causing the cylinder to rotate in the opposite direction. This can help deflect the attack and ensure your doors are secure.

There are cylinders made to resist snapping. This is a growing method of attack on cylinders, where the break line inside the lock is targeted by a tool that is specially designed to snap off the front of the cylinder and allow the door to open. This is a quicker and easier way to gain access than through the use of a multipoint locking system. It also leaves no evidence of the break-in which can make it difficult to prove insurance claims.

Spring Cassette

The spring cassette is positioned inside the base of your door handle's backplate, providing a spring solution and returning your multipoint lock handles to their rest position after use. There was a time when handles did not have a spring integrated into them, and as a result, they tend to droop or 'drop' once the locking mechanism is removed. This simple part is the best way to fix this problem. It also prevents your door from getting stuck in the closed or open position since they aren't easy to close manually.

These spring cassettes were created to be used with a sprung multipoint lock. They will not fit unsprung handles and you'll need to cut a hole in your backplate for them to fit. (Please check the image for a more detailed diagram). They are a replacement upvc door handles for existing broken or missing cassettes in the backplate of the door handle for numerous kinds of uPVC doors. They are available as one unit. They come with a square cut out that can accommodate an 8mm shaft.

These spring cassettes are an excellent value-for-money solution to the issue of door handles that are that are sagging. These spring cassettes are easy to install and will extend the life of your uPVC door. Contact us for more information about our range of uPVC accessories and spares. We are always happy to provide expert advice and to assist you.