• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace upvc door lock to Replace Door Locks

Door locks are the first line of defense against unauthorized access to your home. The signs of wear and tear, and even instances such as moving into a new home or burglaries, could trigger the need to replace lock on upvc door your lock.

To begin, you must determine the size of your cylinder by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will assist you purchase the right-sized lock.

Deadbolt

If you want to ensure your door is secure from criminals, it's a great idea to install deadbolts. The bolt extends into the strike plate that is on the door frame when it's locked, making it more difficult for burglars to gain entry into the door. A single cylinder deadbolt can be activated by keys on the exterior side and a thumb turn device on the inside. A deadbolt is only effective if it's installed correctly however.

The first step is to determine if the door already has a hole for a deadbolt or if it needs to be bored out. Mark the location of the hole to install the deadbolt on top of the door by using the template supplied with your lock installation kit. Use a tape measure to determine the height of the deadbolt. Mark this high point on the door's edge. Use a speedsquare to draw a straightline across the mark you made for the bolthole.

Then, use a drill to drill this area until the hole is on the opposite side of the door. It could take a few minutes. Sand the hole and edge of the door to smooth it. At this point, it's a good idea to stain or paint your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assembly of the deadbolt, as well as the bolt that is inside. Then, remove the bolt and replace it with the new bolt to match the door hardware. It is necessary to remove the bolt from the setplate. After this, you'll need to chisel the area on the door frame for the strike plate.

If your strike plate isn't aligned properly, it's likely because the previous installer didn't correctly mortise it or a weatherstripping was installed and changed the strike position. It is necessary to re-mortise the strike plate and possibly even the deadbolt to fix the issue. Close and lock the deadbolt when you've completed this process. Make sure that the bolt extends into the strike plate then test the key to ensure it is able to open and close easily.

Knob

If a door knob is worn out, it can make your business or home less secure. It can make it more difficult to open or close the door, which is why it's recommended to replace it. replacing upvc Door Lock a knob is a relatively easy DIY project and shouldn't take less than 30 minutes to complete. Make use of pliers or a screwdriver to remove any old knobs or handles. Be careful not to harm other components of the door.

Before you begin you'll need to spray WD-40 or another dry lubricant onto the mechanism of the door knob. This will assist the new lock move smoothly when you turn it. To ensure that it operates properly, it's important to choose the right knob and handle to match the doors you already have. If you don't have a matching knob you'll need to purchase a replacement lock for composite door doorknob and latch plate.

To begin the replacement patio door lock process, first look at the knob or handle to see what screws are holding it in place. If there are no screws, you can use the screwdriver to secure the cover plate between the hidden screws plate.

After you've removed your old knob, examine it for signs of rust or damage. You'll need to clean it off if there are any scratches or marks, but you shouldn't have to do anything major if the knob is in good working order.

Install the new knob. Before you do that, look over the two new knobs to ensure that you're selecting the correct one for your door. You'll want to pick one with an extending rod that is designed to lock with the second knob's rod mechanism. Once you've put the new knob in the hole in the door carefully slide it into the latch.

Test the spring by pressing it repeatedly. The latch should spring back up each time. Install the second knob, and lock it to the rod mechanism of the first knob. Thread the long screws of the interior doorknob into the holes for cylinders on the outside knob and fix it in the knob's position.

Latch

A latch is a piece of metal that extends through the doorjamb to hold it shut. It is operated by a handle or knob on the interior side of the door, or a thumb turn on the exterior side of the door. A deadbolt can be used to secure a latch and prevent intruders from breaking through the glass of the door. It can also protect against accidental or intentional closing by children or animals. The latch can be fitted using a single cylinder deadbolt or double cylinder deadbolts based on the level of security you prefer.

Installing a deadbolt is exactly the same as installing a latch, but there are some differences. First, you must measure the setback of the doorjamb using a tape measure to be sure that the new lock will fit. The setback is measured from the edge of the doorjamb all the way to the center of hole for the latch plate. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If you have a higher setback, you may need to purchase a more substantial latch from a hardware store or locksmith.

The next step is to drill an edge bore hole into the doorjamb for the latch plate. Use a chisel to chisel out the latch mortise, making sure it's deep enough to allow the faceplate of the new latch to sit flush with the doorjamb. Tape the strike plate in place to ensure that it's in the right position.

If the strike is set too high, the door can be pushed in or pressure imposed on it using a crowbar, replacing Upvc door lock or tire iron. This could also cause cracks in the doorjamb. This can be fixed by drilling a new hole in the doorjamb, and cutting the core from the old one.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate over the screw holes that are already in place. Then you can use wood putty to cover the old screw holes and the bolt hole that is not used. Once the putty has dried then sand it to a smooth finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is shut is an electric strike. It is an essential part of the lock's overall security because it stops the door from opening and provides an additional level of resistance to force or kicking. If a door comes with an electronic strike, it can be opened only with a key and the control unit that regulates the electrical impulses.

In the past, putting in an electronic strike required cutting a portion of a doorjamb in order to let the latchbolt of a cylindrical lock from the pocket inside the strike. This change can be an inconvenience when it comes to the aesthetics of an opening as well as exposing the latchbolt and keeper mechanism to any unauthorised users.

Recently, several electric strike manufacturers have developed an innovative type of electric strike, dubbed the "No Cut" strike that doesn't need cutouts in the doorjamb to operate. They use a specific design that allows the latchbolt and keeper to slide into the pocket without damaging the faceplate of the doorjamb.

The strike is fitted with an internal ramp that raises the latchbolt as well as the keeper when it receives an indication from a reader. The latchbolt and keeper are lifted higher up the ramp due to retract. When the door is shut, the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electronic strike is a simple procedure, particularly in the case of replacing patio door lock an existing strike. However, if you're upgrading to an electric strike to use with an access control system, you'll have to ensure that your new system is compatible with the model of lock you've chosen to install. Also, you must make sure that the strike is connected to your access-control system and is configured to function in a fail-safe way.

One method to guard against intrusions by thieves is to upgrade the strike on your doors to a robust strike plate. The plates utilize four to six screws of three inches instead of the two, three-fourth inch screws typically used in regular strikes. These screws are longer, making it harder for someone to break the frame and reach inside to turn the piece that turns the thumb of a single cylinder deadbolt.