• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Lock Replacement - What You Need to Know

It is a good idea for you to replace your locks when they begin to exhibit signs that they're worn out. These signs can include things like difficulty turning the lock or finding a key that doesn't fit.

Fortunately, putting in new hardware for your door locks is actually very easy. All you have to do is follow these steps.

Deadbolt

The deadbolt on your upvc door replacement lock is the primary defense against forced entry. It is more durable and secure than the latch that operates the lock, therefore you should ensure that the deadbolt you purchase is sturdy enough to meet your needs. If possible, choose the deadbolt made of case hardened steel that has no exposed screwheads on the exterior to prevent unauthorized drilling. The interior side of the deadbolt needs to be mortised into your door frame to enhance security.

During the installation, ensure that the bolt of the new deadbolt slides smoothly through the strike plate as you shut and lock the doors. If it does not then use a chisel made of wood to mortise the bolt hole into the strike plate and put the deadbolt back in place. When you lock and close your door, ensure that the latch of the doorknob matches the deadbolt's hole.

Before installing the new deadbolt, ensure whether it's the same size of the old one. The majority of door locks include an example of how far the bolt should be located above the doorknob. However, it's always recommended to consult an expert in hardware for advice if you're not sure what backset size you require for your doors. They should be able to point you towards models that are compatible with your door and the existing deadbolt opening.

After you've confirmed that your new bolt assembly is of the correct length, insert it into the hole in the door. If your new deadbolt is equipped with an opening faceplate, you can screw it in place and secure it, too. It's an excellent idea to screw the latch faceplate with the recommended screws to the frame.

Some lock sets include a "dummy" or decorative bolt so you can install the deadbolt with a key and still have a functioning latch. If you're able to use this feature the dummy bolt must be installed using the same screws that are used for your faceplate of the latch, and it's important that the two bolts are positioned correctly to ensure maximum security.

Some deadbolts are accessible only via a thumb-turn from inside some have two cylinders that allow keys and non-keyed access. Regardless of what kind you pick it's a good idea to buy a commercial-grade lock for the highest level of security. They're typically tested to withstand 250,000 open and close cycles before being sold to homeowners.

Latch

The latch is the part that retracts the bolt whenever you shut or open the door. It's typically held in place by screws on the side of the lock, however it can also be attached to the strike plate or to the inside of the door jamb. It is essential to replace the door latch with the right one for the hardware you have. You can verify this by putting the latch next to your existing hardware or look at the label of the replacement door lock. Dunn Lumber offers a wide range of brands. However, replacing upvc door locks it is recommended to select the same brand that matches your current hardware. This will ensure that the latch you purchase will fit correctly.

Some doors have a hasp instead of a latch. A hasp consists of straps with slots punched into it that fits over the staple. The staple is then nailed to the frame of the door or door with the help of a nail. When the door is closed the strap is pulled down and secures it into position. Commercial buildings utilize a hasp since it is less expensive than the lock.

Locks wear out over time, just like any other mechanism that has moving parts. Sometimes the internal mechanism can "stick" or become difficult to turn. This may require replacement of the entire lockset. Other times the exterior handle or doorknob will fail, requiring to replace it too.

If your lock is stuck, you can try using some graphite in the keyhole. You can either spray it on the key or rub it on the inside of the lock, and then use the lock a few times to get the graphite into the mechanism. You can remove the knob using a screwdriver, which will reveal all the components and let you know what's going on inside.

After taking the knobs off then tighten the three or two setscrews at the edges of the cylinder by turning them clockwise. The faceplate needs to be removed and replaced. Surface-mounted rimlocks come with an additional set cylinder setscrews on the back case that must be removed, as well as the faceplate.

Strike Plate

The strike plate is a way to strengthen and upgrade to the locking system. It is attached to the holes for deadbolts or master key system bolts. It assists in keeping intruders away by ensuring that the lock's latch is caught in the strike plate when the latch or bolt is engaged. In addition to enhancing security, a high-quality strike plate can also improve the durability of the lock.

Standard strike plates are flat pieces of metal with a hole, or several holes cut into them. It is attached to the door frame typically using screws, to give the latch something to sink into when it closes. The strike plate has to be precisely aligned with the lockset to ensure the greatest protection against burglaries.

If the strike plate on a replacing upvc door lock mechanism is damaged, you must replace it as soon as possible. This will ensure that the door will close and latch properly. To replace a strikeplate first check that it is properly aligned with the bolthole of the doorjamb. This can be done by placing a piece adhesive tape over the bolt hole, and then attempting to test the latch. If the latch doesn't catch, Replacing Upvc Door Locks remove the tape and chisel the area so that the striker will be flush with the doorjamb.

After the area is removed it is essential to use a larger screw to secure the strike plate. The screws should be at minimum three inches long to ensure they are securely fixed to the stud that is behind the trim board. If you do not use the screws that are longer and the wood in the doorjamb could split in the event of a kick-in attack by a burglar and leave the door vulnerable.

A professional locksmith can quickly replace a strike plate that's been damaged or worn. They can also install new strike plates on doors that never been fitted with them before. Additionally, they can upgrade existing strike plates to improve a building's security and improve appearance. This could assist property owners in attracting tenants who want a secure living environment and more peace of mind.

Keys

The key cylinder is the part of your lock that accepts a specific key that allows pins to be moved into place so the inner handle can be turned. The key cylinder is also the most crucial component of your door lock because it carries out the function that locks were made to protect you, your family and your belongings. It is for this reason that people frequently have their locks rekeyed rather than replacing upvc door locks them.

It is more difficult to change replacing a upvc door lock lock than to simply switch out the existing handle and deadbolt. Changing the entire lock requires taking the old cylinder and hardware from the door (including the handle when you have a knob lock combo) and installing a new one in its place. There are many DIY-friendly kits that can be used to replace a door lock. However, it's recommended to speak with a locksmith to make sure the work is done correctly.

Before installing a new cylinder and lock it is crucial to have the right key for your home. A key that is a duplicate will not work properly and could even cause the lock to fail completely, rendering it impossible to open. A skilled professional can help you avoid this by ensuring that you have a genuine, functional key for your home.

Next, you will need to remove the faceplate and latch plate. You'll need a screwdriver to remove the screws that hold them in place. You might want to keep them in place if the new plates are identical to the original ones. This will help you save time. If you need to replace them, be careful not to tighten screws too much as this could cause them to lose their grip.

After you have removed the plates, you will need to measure the new locks. It is crucial to know the door's dimensions before visiting the hardware store. Although a lot of locksets available today will fit a standard door thickness, it's better to have them in advance. Be aware that doorknob locksets will often be different sizes than deadbolt locksets and that commercial models can come with an enlarged latch or bolt.