• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged window replacement panes pane could be a nuisance. It could also be a chance to upgrade your glass to energy efficient or insulated windows and enjoy benefits such as greater comfort, a higher potential for resales, and less costs.

You can do it yourself at less than what it would cost of windows replacement to employ an expert. You'll only require the proper tools and a few hours of your time.

Glass

If your single-pane windows are outdated broken, deteriorating or damaged replacing them with more modern glass that is tempered or insulated can improve energy efficiency and reduce noise while preserving the historic integrity of older homes. The process of replacing a window pane is relatively easy and can be accomplished by homeowners with basic hand tools. In addition to a replacement pane, the following items are required for the replacement process: latex glazing putty glazier's points; pliers; and the use of a heat gun to warm the old putty, if necessary. Wear safety goggles and gloves before you begin. Working with broken glass can cause serious injuries.

Begin by removing any remaining broken pieces of glass. It is recommended to use pliers for this however a flathead could be used as well. Then, use a wooden chisel or putty knife to remove the remaining old putty from around the frame and the sash. Be careful not to break the window sash. Be careful and slow. This can be done best on a ladder, not the ground. Also, have someone lower to ensure it is held steady.

After you have removed all the old putty, you can prepare the window frame to accommodate the new pane. Take measurements of the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to a hardware or home center store to have a piece cut of glass stock to the proper size. Alternately, you can cut the glass yourself if have the appropriate tools.

After putting in the new pane after installing the new pane, put a tiny amount of caulking around the edge to ensure it is weatherproof. Install a glazier's pointing on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they cause friction between the sash and frame but they should not be too loose.

Before applying the putty on the surface, gently knead it until it becomes soft and free of lumps. Then you can roll it into pencil-sized strips. Apply the first strip to the corner of the frame. Work from one corner to another and ensure that it is even and smooth.

Glazier's Points

The glazier’s points are small triangular pieces of metal which help to secure the glass into the window frame without causing any damage to the fragile surface. Understanding how to use these little helpers is easy and can save you money on a professional installation or the cost of buying new glass.

After taking off the old putty, glazier points as well as any remaining residue clean the frame thoroughly using a utility knife. If needed, lightly sand the wood in the grooves of the rabbets to smooth out rough spots. If you decide to sand wood, cover it with painter's tape to prevent accidental damage.

Measure the empty frame's dimensions and write down accurate measurements. These dimensions can be taken to an hardware or home centers store and the new pane will be cut a bit smaller. This will ensure a snug fit and leave room for expansion and contraction.

Place the new pane into the frame and push firmly with your hands. Then, use the tip of your chisel or back end of the putty knife to pierce the glazier's facets, as shown in Figure 11. The glazier's points should be in line with the top edge of your pane and the shoulders raised should be just below that lip.

Apply a thin layer of glazing compound on the rabbet grooves and the edges of the new glass. This will seal and protect the edges. Let it dry completely and cure.

Install the new window sash once the glazing compound has dried. First, coat the wood with a thick coat of Linseed oil. This will prevent the new putty from sucking up moisture and deteriorating and cracking over time. Apply the coating using a brush this coat, or even the tip of the putty blade. Then, use the chisel that is on the back of the tool or the back of the handle to gently smash the new sash or glazier's point into the rabbet grooves. Repeat this procedure every 10 inches along the frame's perimeter.

Putty

A baseball that is thrown or an unintentional rock, or falling branch could cause a window pane to crack or break. Most windows can be replaced by simply putting in a fresh piece. The glass is held in place with small clips made of metal called a glazier's point and putty, often called glazing compound. Before you install a new pane, first get rid of the old one and clean the area with a rag and an abrasive scraper that is a pull type or the wood chisel. Wear safety glasses and gloves when you work. If the window is attached to the frame, you'll need to make use of a heat gun to soften the adhesive prior to prying it free.

If you're planning to reinstall your original sash, you must remove the molding that holds the old pane. Sand the sash until it is flat and ready to receive new caulk. Once the sash is put back in place, you can apply a silicone caulk over the glass. This will ensure that it won't leak over time or discolor.

Remove the glazing points from the rabbets. These are the grooves in the sash, where the glass is. If they're difficult to chisel, use the hand tool, such as a heating gun over them to allow them to soften before. If you're using a heating gun, make sure not to damage the railings of the sash or the sash itself by holding the tool too close.

Make a bed for your new pane after removing the old glaze and putty. Roll a rope of glazing compound between your hands, forming it to be around 1/2-inch thick. Place it into the rabbets where the glass will be placed. The glass should rest against the putty on both sides. If you need to you want to tap your glass lightly into the rabbet using your thumb.

If the new pane is cracked you can fill it with a solvent-based glue or silicone caulk prior pressing it into the sash. If the crack is not sealed, you'll need to use putty to keep water from getting in. After the putty has dried, wipe the oily film off the glass and allow it to dry completely before you paint. If you paint before the putty has completely dry, it won't create a solid seal and could leak or discolor over time.

Paint

You might be worried about replacing a broken piece of glass. However, replacing a single glass pane doesn't require a huge amount of money If you can do it yourself. Even double-paned windows can be replaced for a fraction of the price it costs an expert.

If you are working with large glass replacement for windows near me windows first ensure it is securely fixed to the frame. This job can be done relatively easy and fast with the appropriate tools and techniques.

Once you're ready to begin, begin by removing the old window by prying out the metal glazing points that are connected to it. These are tiny metal triangles that function as "nails", holding the Upvc window lock replacement in the frame. They are placed under a bead or glazing putty that sets to form solid wedge which holds the wood frame in place and conceals the edges.

Once you have the old pane taken away Clean up the frame and wood. Scrape off any old paint and sand down the rabbet grooves that the glazing points were placed. Sand them to bare wooden surfaces so you can paint the frames with the same color. After sanding, apply a coat of flax oil to the wood's surface to extend the life of the frame.

The next step is to measure the dimensions of the window opening. You will need to take horizontal and vertical measurements of the entire opening as well as the thickness of the old pane. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal changes. You can bring these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.